CWSI WRA-3 Operating And Installation Instruction Manual Download Page 6

 

P/N IM-WRA-3 Rev. A 

 2012 Commercial Wireless Systems International, LLC. 

Section 2 - Compatibility 

2.1 Compatible Equipment and Accessories 

The following UL Listed RF products are compatible with the WRA-3 annunciator: 

Commercial Wireless Systems International, LLC 
CP-3000A(DA) – Control Panel 
AR-3A - Repeater 
Smoke Detector Model 300 – Photo Electric Smoke Detector with Integral Sounder 
Tandem Smoke Detector Model 301- Photo Electric Tandem Smoke Detector with Integral Sounder 
Smoke Detector Model 302 – Photo Electric Smoke Detector without Sounder 
Pull Station Model 310 – Manual Pull Station 
Fire Transmitter Models - 340(TS) – N.O. EOL Supervised Transmitter 
CO Detector Model 350 – Carbon Monoxide Detector with Integral Sounder 
 

The following antennas are for use with the WRA-3 annunciator: 

Commercial Wireless Systems International, LLC 
Model OM-1 Omni – Isotropic gain 2.5 dBi 
 

 

 
 

 

Section 3 - Installation 

 

3.1 Preparing the Installation Site 

A signal survey must be performed by a factory trained technician or authorized dealer prior to the 
installation of the WRA-3 annunciator. The signal survey determines an acceptable location to mount 

Summary of Contents for WRA-3




















Reviews: