Cutters Edge CE-1270RH SERIES Operator'S Manual Download Page 15

CUTTERS EDGE  

  

14

770

/970/12

7

0 Model

Operating

Protective equipment

General

• Do not use the machine unless you are able to call for

help in the event of an accident.

Personal protective equipment

You must use approved personal protective equipment 

whenever you use the machine. Personal protective 

equipment cannot eliminate the risk of injury but it will 

reduce the degree of injury if an accident does happen. 

Ask your dealer for help in choosing the right equipment.

!

WARNING! The use of products such as 

cutters, grinders, drills, that sand or form 

material can generate dust and vapors 

which may contain hazardous chemicals. 

Check the nature of the material you 

intend to process and use an appropriate 

breathing mask.

Long-term exposure to noise can result in 

permanent hearing impairment. Always 

use approved hearing protection.   Listen 

for warning signals or shouts when you 

are wearing hearing protection. Always 

remove your hearing protection as soon 

as the engine stops.

Always wear:

• Approved protective helmet
• Hearing protection

Ey

e protection.

R

espiratory protection

• Heavy-duty, firm grip gloves.
• Tight-fitting, heavy-duty and comfortable

clothing that permits full freedom of

movement.

• Boots with steel toe-caps and non-slip sole

Other protective equipment

• Fire Extinguisher
• Always have a first aid kit nearby.

!

CAUTION! Sparks may appear and start a fire 

when you work with the machine. Always keep 

fire fighting equipment handy.

General safety precautions

This section describes basic safety directions 

for using the machine. This information is never 

a substitute for professional skills and 

experience.
• Please read the  operator’s manual carefully

and make sure you understand the

instructions before using the machine. It is

recommended that first time operators also

obtain practical instruction before using the

machine.

• Keep in mind that it is you, the operator that is

responsible for not exposing people or their

property to accidents or hazards.

• The machine must be kept clean. Signs and

stickers must be fully legible.

Always use common sense

It is not possible to cover every conceivable situation you can face. Always 

exercise care and use your common sense. If you get into a situation where you 

feel unsafe, stop and seek expert advice. Contact your dealer, service agent or an 

experienced user. Do not attempt any task that you feel unsure of!

!

WARNING! The machine can be a dangerous tool if used 

incorrectly or carelessly, which can cause serious or 

fatal injury to the operator or others.

Never allow children or other persons not trained in the 

use of the machine to use or service it.

Never allow anyone else to use the machine without first 

ensuring that they have read and understood the contents 

of the operator’s manual.

Never use the machine if you are fatigued, while under the 

influence of alcohol or drugs, medication or anything that 

could affect your vision, alertness, coordination or 

judgement. 

!

WARNING! Unauthorized modifications and/or 

accessories may lead to serious injury or death to the 

user or others. Under no circumstances may the design of 

the machine be modified without the permission of the 

manufacturer.

Do not modify this product or use it if it appears to have 

been modified by others.

Never use a machine that is faulty. Carry out the safety 

checks, maintenance and service instructions described 

in this manual. Some maintenance and service measures 

must be carried out by trained and qualified specialists. 

See instructions under the heading Maintenance.

Always use genuine accessories.

Your warranty may not cover damage or liability caused 

by the use of non-authorized accessories or replacement 

parts.

WARNING! This machine produces an electromagnetic 

field during operation. This field may under some 

circumstances interfere with active or passive medical 

implants. To reduce the risk of serious or fatal injury, we 

recommend persons with medical implants consult their 

physician and the medical implant manufacturer before 

operating this machine.

Summary of Contents for CE-1270RH SERIES




































Reviews: