CustomWorks 0918, Manual

Page: 11 / 16

Clutch Bag Clutch Bag
Clutch Bag Clutch Bag
Clutch Bag
Clutch Assembly Clutch Assembly Clutch Assembly Clutch Assembly Clutch Assembly
-Parts for
Clutch
Bag
5208 Qty 1
M3x6mm SH 4439 Qty 1
Clutch Bearing
4430 Qty 1
Flywheel
- Slide the 4437 Collet onto you motor followed by the 4430 Flywheel.
- Secure the Flywheel using 4442 SG Nut.
- Place the 4435 Clutch Shoes onto the clutch facing the direction shown and
secure with 4431 Clutch Springs.
NOTE: Install the springs by placing one leg on the Shoe, then press the other
leg into the groove in the Clutch Nut using a Driver Wrench.
- Slide 4438 Bearing onto the motor shaft followed by the 4440 Clutch Bell then
the 4439 Flanged Bearing.
- Secure the assembly using 5208 Screw. The clutch bell should spin “FREELY”
with the screw tight. It is OK if the clutch bell slides back and forth on the
motor shaft slightly. If there is too much play use the extra shims provided
to correct this.
- Thread the 4523 Pinion Gear onto the Clutch Bell with the side of the pinion
with the threads all the way to the edge facing AWAY from the motor.
4438 Qty 1
Flanged Bearing
4523 Qty 1
23T Pinion 4440 Qty 1
Clutch Bell 4431 Qty 2
Clutch Spring 4435 Qty 2
Clutch Shoe 4442 Qty 1
SG Nut 4437 Qty 1
Collet
5208
4438
4523
4440
4439
4431
4435
4442
4430
4437
Body Mounts Body Mounts Body Mounts Body Mounts Body Mounts
Body Mounts Body Mounts
Body Mounts Body Mounts Body Mounts
-Parts for
Body
Mounts
- Slide the Post Collar onto the 3229 Short Body
Post, use the Set Screw to retain the Collar
- Mount the (2) 3229 Short Body Posts to the for-
ward set of holes on the 3012 Bumper.
- Attach the 3012 Bumper to the 1287 Front Clip
using 5283 Screws and 5207 Nuts.
- Mount the 1287 Front Clip to the Chassis in the
second set of holes from the front edge of the
chassis using 5253 Screws and 5217 Nuts.
5253 Qty 4
4-40 x 3/8 BH Screw
1:1
3012
3229
COLLAR
5283
1004
5253
5283 Qty 4
8-32 x 1/2 FH Screw
1:1
3229 Qty2
Post Collar
5207 Qty 4
8-32 Lock Nut
5217 Qty 2
4-40 Lock Nut
1287 Qty1
INT Front Clip
3229 Qty2
Short Body Post
3228 Qty2
Long Body Post
3012 Qty1
INT Front Bumper 1004 Qty 1
Rear Body Mount
- Mount the (2) 3228 Long Body Posts to the
1004 Rear Body Mount.
- Attach the 1004 to the Trans Brace using
5253 Screws and 5217 Lock Nuts.
5217
FRONT
REAR
5207
SET SCREW
3229 Qty 2
Set Screw
3228
POST
5283
5283
1287
3229
POST
5253