Custom Audio Electronics TG02H Command Manual Download Page 62

Page: 62 / 100

STATUS COMMAND

0x10 0x04

<DLE EOT>

Real-time status transmission

Valid for

TG02H

[Format]

ASCII

DLE EOT n

Hex

10 04 n

Decimal

16 4 n

[Range]

1 ≤ n ≤ 4

n = 17

n = 20

n = 21

[Description]

Transmits the selected printer status specified by n in real time according to the following parameters:

n = 1

transmit printer status

n = 2

transmit off-line status

n = 3

transmit error status

n = 4

transmit paper roll sensor status

n = 17

transmit print status

n = 20

transmit FULL STATUS

n = 21

transmit printer ID

[Notes]

• Immediately executed even when the data buffer is full.

• This status is transmitted whenever data sequence 0x10 0x04 is received.

[Default]

[Reference]

See tables below.

[Example]

n=1: Printer status

BIT OFF/ON

HEX

DECIMAL

FUNCTION

Off

Not used. Fixed to Off

Not used. Fixed to On

Off

Not used. Fixed to Off

Off

On-line.

Off-line.

Not used. Fixed to On

RESERVED

62 │

ESC/POS™ emulation

Summary of Contents for TG02H





































































































Search results

Summary of Contents for TG02H

Reviews:

Related manuals for TG02H

Brands by name

Popular brands

Custom Audio Electronics TG02H, Command Manual

Search results

Summary of Contents for TG02H

Reviews:

Related manuals for TG02H

Brands by name

Popular brands