Custom Audio Electronics TG02H Command Manual Download Page 6

Page: 6 / 100

The fields shown in the scheme of the previous figure have the following meaning:

[Format]

ASCII, hexadecimal and decimal command value.

[Range]

Limits of the values the command and its variables can take

[Description]

Description of command function

[Notes]

Additional information about command use and settings .

[Default]

Default value of the command and its variables.

[Reference]

Pertaining commands related to described command.

[Example]

Example of using the command

Listed below are the meanings of some of symbols that may be found in the command description:

indicates the representation of the command hexadecimal value (for example 0x40 means HEX 40).

n, m, t, x, y

are optional parameters that can have different values.

6 │

Introduction

Summary of Contents for TG02H





































































































Search results

Summary of Contents for TG02H

Reviews:

Related manuals for TG02H

Brands by name

Popular brands

Custom Audio Electronics TG02H, Command Manual

Search results

Summary of Contents for TG02H

Reviews:

Related manuals for TG02H

Brands by name

Popular brands