background image

B

114

Repair and Service Manual

ENGINE

Read all of SAFETY and this section before attempting any procedure. Pay particular attention to Notices, Cautions, Warnings and Dangers.

653045

Changing the Oil

Tool List

Qty.

Socket, 19 mm.............................................................1
Ratchet ........................................................................ 1
Extension, 8" ...............................................................1
Oil Filter Wrench..........................................................1
Oil Drain Pan ...............................................................1
Shop Towels .............................................................AR

For maximum performance and longevity, the engine oil 

should be replaced after the first 8 hours of operation. 

After the initial oil change, it should be changed every 125 

hours of operation or semi-annually, whichever comes 

first.
The selection of oil is dependent upon the service that the 

vehicle will perform. Most vehicles require 10W-30 oil, 

whereas vehicles used at capacity or near capacity load 

applications will utilize 10W-40 oil after a break-in period 

of 100 hours (Ref. Fig. 3).

Fig. 3  Oil Viscosity Chart

NOTICE: If vehicle is to be stored over the winter 

months, it can be stored with the old oil left in 

engine. The oil should be changed as part of spring 

maintenance to remove any moisture that has accu-

mulated during storage.

Engine fluids can be hot and con-

tact with the skin can cause severe 

burns. Wear rubber gloves to pro-

tect skin from exposure to the old oil and degreaser.

The oil should be changed with engine warm. Park the 

vehicle on a level surface, engage parking brake and 

remove the key from the vehicle (Ref. Fig. 4).

Fig. 4  Cleaning Top of Engine

Be careful of hot oil when drained. It 

may be hot enough to burn you 

severely.

1.

Wipe the top of the engine clean with a cloth. 

Remove the oil fill cap.

2.

Place an oil drain pan under the oil drain plug (1) 

(Ref. Fig. 5) found at the rear of the engine base.

3.

Remove the drain plug (1). Allow the oil to drain into 

the drain pan.

Fig. 5  Oil Drain Plug

4.

Before installing the drain plug (1), clean the area 

around the drain plug hole with a lint free cloth.

5.

Inspect the drain plug (1) for damage; replace if nec-

essary (Ref. Fig. 5). If the o-ring (2) on the drain plug 

is damaged, replace it with a new one. 

6.

Tighten the drain plug (1) to the torque value speci-

fied below.

At the first oil change, 

small

 metal particles can be pres-

ent. This is normal and is a result of the engine break-in 

process. Inspect the filter at every oil change. The pres-

ence of large metal chips can indicate possible damage to 

-20

0

20

40

60

80

100

-30

-20

-10

0

10

20

30

40

C

F

10W-30

10W-40

HEAVY DUTY WORK

LIGHT DUTY WORK

(AIR TEMPERATURE)

10W-30

Item

Torque Specification

1

61 in. lbs (7 Nm)

Oil Fill Cap

1

2

Property of American Airlines

Summary of Contents for HAULER 1200

















































































































































































Reviews: