CUSHCRAFT MA5B Assembly And Installation Instructions Manual Download Page 12

SPECIFICATIONS

Model

MA5B

Frequency 

Ranges

10 12 15 17

 

20 

meters

Elements

2

1

2

1

per band

Gain

5.3

1.0

4.8

1.0

3.6  

dBi

Front to Back Ratio

10

0

12

0

22 

dB

Sidelobe Attenuation

25

25

25

25

25 

dB

VSWR 2:1 Bandwidth

665

>

110 225

>

100 90 

kHz

Longest Element

17.1

ft.  

(5.2

m

)

Turning Radius

8.8 

ft.   

(2.7

m

)

Boom Length

7.3 

ft.   

(2.2

m

)

Boom Diameter

1.5

in.   

(3.8

cm

)

Max. Wind Surface Area

3.22

ft 

2

 

(.3

m

2

)

Max. Power Handling

1.2 

kw

Weight

26.5 

lbs. 

(12

kg

)

LIMITED WARRANTY

Cushcraft Corporation, 48 Perimeter Road, Manchester, New Hampshire 03103, warrants to the original purchaser for one
year from date of purchase that each Cushcraft antenna is free of defects in material or workmanship.  If, in the judgement
of Cushcraft, any such antenna is defective, then Cushcraft Corporation will, at its option, repair or replace the antenna
at its expense within thirty days of the date the antenna is returned (at purchasers expense) to Cushcraft or one of its
authorized representatives.  This warranty is in lieu of all other expressed warranties, any implied warranty is limited in
duration to one year.  Cushcraft Corporation shall not be liable for any incidental or consequential damages which may
result from a defect.  Some states do not allow limitations on how  long an implied warranty lasts or exclusions or limitations
of incidental or consequential damages, so the above limitation and exclusion may not apply to you.  This warranty gives
you specific legal rights, and you may also have other rights which vary from state to state.  This warranty does not extend
to any products which have been subject the misuse, neglect, accident or improper installation.  Any repairs or alterations
outside of the Cushcraft factory will nullify this warranty.

48 PERIMETER ROAD, MANCHESTER, NH 03103 USA

TELEPHONE: 603-627-7877 • FAX: 603-627-1764 • E-mail: [email protected]

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

MA5B

The Electrical Specifications for all Cushcraft Amateur Antennas are derived from numerical analysis and
measured data taken on our test range.  Performance may vary due to the random variables associated
with a specific application or installation.

Summary of Contents for MA5B













Reviews: