manualshive.com logo in svg

Cuscini ABRI, Step By Step Assembly Instructions, Page: 9 / 10

Share
Download
Cuscini ABRI Step By Step Assembly Instructions Download Page 9

of 10

Installing the Roof Fabric

9

14

13

Install plastic pulleys 

 by snapping them in each 

[MISC K.PL101]

metallic curtain eyelet. Pulleys should be facing towards the 

curtain side on which the zipper is located (see above steps). 

Then install each curtain sections into the provided beam slots 

as shown by left hand diagram. After installing all pulleys, block 

the access with the screws

 as shown in the 

 [KC14.BL3015]

diagram. Repeat step for each corner. See next step (15) for 

curtain installation example.

Profile View

Zipper

(Interior Side)

Metallic

Eyelet

Curtain

(Exterior Side)

Curtain

Exterior Side

Plastic Pulley

Snap Pulley

in place

BL3015

P2

To complete the post assembly, snap together the corner posts 

[P1]

[P2]

 and corner post covers 

 using a rubber hammer as 

shown in the diagrams above. Repeat step for each corner.

Top View

P1

P1

P2

P2

K.PL101

Roof truss not shown for clarity

Model # Pavillion 1.0

Distributor: ShadeScapes Americas

970.527.7070

cuscini.shadescapesamericas.com

Summary of Contents for ABRI











Reviews:

No comments