background image

 

 
 
 

USING THE REMOTE CONTROL 

Installing batteries 

 

 

    

 

 

 

Notes: 

 

Use only the size and type of batteries 
specified. 

 

Do not mix different types of batteries 
together or old batteries with fresh ones. 

 

Remove the batteries when remote 
control will not be used for a long period of 
time. 

 

Avoid direct sunlight, incandescent lamp, 
fluorescent lamp or any other strong light 
shines on batteries. 

 

Do not try to recharge batteries; they are 
not intended to be recharged. 

 

Do not drop, dampen or disassemble 
the remote control. 

 

When the batteries are about to wear out, the remote control may be unstable.   

 

Do not throw the batteries into a fire; dispose of used batteries in the specified 
manner.  

POWER ON/OFF 

To Switch the TV Set On and OFF 

When the TV is plugged into an AC outlet, the main POWER is ON and the TV is in Standby mode. 
The TV set can be put in stand-by mode (OFF) or ON by pressing the “Power on/Standby” button 
on the remote control or by pressing the Main Power Switch in front of the TV. 

Notes: 

 

Please unplug the AC cord when you may not use the unit for an extend period of 
time. 

Effective Range of the

Summary of Contents for TV2710















Reviews: