background image

13 of 14

Optional Auxiliary By-Pass Control Valve (PN: 9PKFELBV)

       • Installation of this Curtis Auxiliary Control Valve retains the Tractor/Loader's Bucket Cylinders for down pressure

       • The Curtis Auxiliary Control Valve is Universal in nature.

       • Carefully consider mounting location before proceeding.

       • Due to Tractor variations, Curtis only supplies Hoses and Fittings between the Angle Cylinders and Curtis By-

         Pass Relief Valve. All additional Hoses, Fittings and Couplings are Dealer/Customer supplied.

 

1.) 

Determine convenient location to mount Auxiliary Control Valve.

 

     If Loader is Quick Attach Style, consider mounting Valve to remain with Tractor/Loader when detached.

 

2.)

 Disconnect Pressure Supply Line from existing Tractor/Loader Valve. 

 

3.)

 Route Tractor/Loader Pressure Supply Line to Inlet Port marked 

"IN"

 on Auxiliary Control Valve.

 

4.)

 Route a Dealer supplied Line from Outlet Port marked 

"OUT"

 on Auxiliary Control Valve to Pressure Port on

 

     existing Tractor/Loader Valve.

 

5.)

  Route two additional Dealer Supplied Hoses from Ports marked 

"A"

 and 

"B" 

on existing Tractor/Loader Valve

 

      down along Tractor/Loader Arms to corresponding 

"A"

 and 

"B"

 ports on Curtis By-Pass Relief Valve.

 

 

 

Curtis Auxiliary By-Pass Control Valve Port designations are for reference only.

 

6.)

 Route Curtis Supplied Angle Hoses from 

"C"

 and 

"D"

 Ports on Curtis By-Pass Relief Valve to Left and Right

 

     Angle Cylinders.

 

7.)

 Check all Hydraulic connections and test operation. Inspect for leaks.

 

 

 

Seal all N.P.T. (National Pipe Thread) connections with a Paste Type Thread Sealer

 

 

 

(e.g. 3M, Great White) DO NOT use Teflon Tape. Teflon Tape may contaminate Hydraulic    

 

 

 

System and cause a malfunction.

IMPORTANT

Figure 16 . Hydraulic Routing Diagram

A

B

D

C

To Control Valve

Right Angle Function

To Control Valve

Left Angle Function

A

B

IN

OUT

Tractor Hydraulics

Pressure Hose

To "B" Port on

By-Pass Relief Valve

To "A" Port on

By-Pass Relief Valve

Attach Control

Lever Here

To Tractor

Loader Valve "IN"

SUPPLIED HOSE

SUPPLIED HOSE

Left

Angle

Cylinder

Right

Angle

Cylinder

Auxillary Loader Control Valve

Curtis By-Pass Relief Valve

NOTE

IMPORTANT

Summary of Contents for Sno-Pro 5FBMQA















Reviews: