Curtis Mathes CMC13101 Owner'S Manual Download Page 10

Page: 10 / 52

Chapter 1 : Overview of Your Equipment

C H A P T E R

Overview of Your Equipment

Your TV/VCR Combination’s comes with a remote control. The section below summarizes
the buttons, controls, and terminals that you will use with your TV/VCR Combination.

Your TV/VCR Combination's Front Panel

Below you will find short description of the buttons and indicators on the front panel. These
are used for the following functions:

VIDEO in jack

Use this jack to receive a video signal from another A/V component.

AUDIO in jack

Use this jack to receive a audio signal from another A/V component.

EAR PHONE jack

Use this jack to the earphone (not supplied). The sound from the speaker is turned off.

Remote control receiver

This receiver receives a signal from your remote control. Do not block it.

STAND-BY(red) indicator

This indicator lights up when the power is off.

REC (red/green) indicator

This indicator lights up red when recording and lights up green when timer program oper-
ating.

REC button

Press this button to begin recording. Press repeatedly to set a recording time using
One-Touch Recording (OTR).

REW button

Press this button to rewind the tape.

PLAY button

Press this button to begin normal playback of the tape

10 FF button (Fast Forward)

Press this button to fast forward the tape.

VIDEO AUDIO

REC

1 2

POWER

STAND-BY REC

EAR PHONE

REW PLAY FF

STOP/EJECT

VOL CH

Summary of Contents for CMC13101





















































Search results

Summary of Contents for CMC13101

Reviews:

Related manuals for CMC13101

Brands by name

Popular brands

Curtis Mathes CMC13101, Owner'S Manual

Search results

Summary of Contents for CMC13101

Reviews:

Related manuals for CMC13101

Brands by name

Popular brands