GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
WARNING: ALL NON-TRAILER (WHEEL-LESS) LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY 18050 STABILIZING STRAPS.
WARNING:
** FAILURE TO PROPERLY SUPPORT NON-TRAILER LOADS WILL VOID PRODUCT WARRANTY **
WARNING: *** DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY ***
FOR MORE INFORMATION LOG ONTO WWW.CURTMFG.COM
HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-800-798-0813
HITCH WEIGHT: LBS.
INSTALL TIME
PROFESSIONAL: MINUTES
NOVICE (DIY): MINUTES
INSTALL NOTES:
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
CURT Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser.
If the product is found to be defective, CURT Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid,
with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. CURT Manufacturing LLC.'s liability is limited to
repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.Regulation V-5 and SAE J684.
3,500
350
25
25
MITSUBISHI ECLIPSE CROSS
4/4/18
12154
60
Scan
for more
information
Parts List
DESCRIPTION
PART NUMBER
QTY
ITEM
CARRIAGE BOLT
1/2-13 x 4 1/2
4
1
HEX FLANGE NUT
HFN 1213, GR8
4
2
HEX BOLT
M10 - 1.25 x 25
2
3
CONICAL TOOTHED WASHER
3/8"
2
4
SPACER
12154-SP
2
5
PASSENGER SIDE
FRAME RAIL
DRIVER SIDE
FRAME RAIL
1. Lower exhaust by removing the (2) rubber hangers by the muffler and (1) rubber hanger just forward of the muffler.
NOTE:
Be sure to support the exhaust when removing the rubber hangers.
2. If present, remove the tow loop on the passenger side of the vehicle frame. Return tow loop and bolts to vehicle owner.
3. Place (2) bolts through each 12154-SP plate and install thought the frame as shown in the diagram above. Temporary
removal of the (1) fastener supporting the canster on the driver side frame rail will aid access but is not required.
4. Raise hitch into position and slide the bolts through to support it. Loosely install the supplied hex flange nuts and the (2)
hex bolts and conical washers as shown. Be sure teeth on washers are against the hitch mounting plate.
5. Torque all 10mm fasteners to 48 lb-ft and all 1/2" fasteners to 110 lb-ft.
6. Reinstall canister fastener, if removed, and rubber exhaust hangers.
- LOWER EXHAUST
- REMOVE TOW LOOP
- NO DRILLING REQUIRED
- NO TRIMMING REQUIRED
TOOLS REQUIRED
RATCHET
TORQUE WRENCH
6" EXTENSION
3/4" SOCKET
14mm SOCKET
17mm SOCKET
SAFETY GLASSES
DESIGNED FOR
USE WITH BALL
MOUNT # 45521
EURO MOUNT
OPTIONS AVAILABLE
# 45571 (1 7/8" BALL)
# 45572 (2" BALL)
1
5
4
3
2
Summary of Contents for 12154
Page 4: ......