Curt Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,
Curt Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of
this product voids the warranty. Curt Manufacturing LLC.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or
consequential loss or damage.
KEEP IN VEHICLE FOR FUTURE REFERENCE
60640 QUICK GOOSE 2 Page 4 of 6
P
P
P
PE
E
E
ER
R
R
RI
II
IO
O
O
OD
D
D
DI
II
IC
C
C
CA
A
A
AL
L
L
LL
L
L
LY
Y
Y
Y C
C
C
CH
H
H
HE
E
E
EC
C
C
CK
K
K
K T
T
T
TH
H
H
HI
II
IS
S
S
S H
H
H
HI
II
IT
T
T
TC
C
C
CH
H
H
H T
T
T
TO
O
O
O I
II
IN
N
N
NS
S
S
SU
U
U
UR
R
R
RE
E
E
E T
T
T
TH
H
H
HA
A
A
AT
T
T
T A
A
A
AL
L
L
LL
L
L
L F
F
F
FA
A
A
AS
S
S
ST
T
T
TN
N
N
NE
E
E
ER
R
R
RS
S
S
S
A
A
A
AR
R
R
RE
E
E
E T
T
T
TI
II
IG
G
G
GH
H
H
HT
T
T
T A
A
A
AN
N
N
ND
D
D
D T
T
T
TH
H
H
HA
A
A
AT
T
T
T A
A
A
AL
L
L
LL
L
L
L S
S
S
ST
T
T
TR
R
R
RU
U
U
UC
C
C
CT
T
T
TU
U
U
UR
R
R
RA
A
A
AL
L
L
L C
C
C
CO
O
O
OM
M
M
MP
P
P
PO
O
O
ON
N
N
NE
E
E
EN
N
N
NT
T
T
TS
S
S
S A
A
A
AR
R
R
RE
E
E
E S
S
S
SO
O
O
OU
U
U
UN
N
N
ND
D
D
D....
60640 OPERATION
1) To raise Ball to the towing position, rotate the Red Grip Choker Pull Rod 45 degrees clockwise and pull to its
full extension. Spring tension should raise the Ball. Typically further assistance is not required, however, in the
event assistance is required, push in on the Black Grip Linkage Pull Rod while maintaining the Red Grip Choker
Pull Rod at its full extension.
2) When the Ball rises, allow Red Grip Choker Pull Rod to retract inward while still maintaining its 45 degree
orientation. Full locking of the Choker is
ONLY
accomplished when the Pull Rod retracts to its full Choker
insertion position. When this occurs, rotate the Choker Pull Rod 45 degrees counterclockwise back to its
POINTING DOWNWARD POSITION
. This ensures the Choker is fully inserted and locked.
UNDER NO
CIRCUMSTANCES HOOK-UP TO THE BALL UNLESS THE PULL ROD IS FULLY ENGAGED AND ROTATED
AS DESCRIBED.
3) To lower the ball after uncoupling the trailer, once again rotate the Red Grip Choker Pull Rod 45 degrees
clockwise and pull to its full extension. While maintaining full extension, pull outward on the Black Grip Linkage
Rod. The Ball will drop to its lower position.
4) While maintaining full extension of the Black Grip Linkage Pull Rod, allow the Red Grip Choker Pull Rod to
retract inward while maintaining its 45 degree orientation. Once again, rotate the Pull Rod 45 degrees
counterclockwise to its pointing downward position. Release the Black Grip Pull Rod. The Ball is now locked in
its downward position.
5) Insert Rubber Logo Dust Cap when ball is down (not towing).
60640 Coupling Inspection
1) Raise Hitch Ball and lock as previousely described. Connect trailer to the Hitch Ball. Check clearances.
There should be a minimum of 6 inches of clearance between the bottom of the trailer overhang and top of the
bed sides. Verify clearance between lower front of trailer and corner of bed or bumper and between the upper
front corner of the trailer and the rear of the cab.
60640 Maintenance
1)
IMPORTANT...
Keep clean and lubricated to ensure proper functioning. For your convenience, the Red Grip Choker Pull Rod
has a secondary locking position.
DO NOT HOOK TRAILER TO BALL WHEN PULL ROD IS IN THE
FOLLOWING POSITION. THE BALL IS NOT LOCKED / DO NOT TOW. SERIOUS DAMAGE TO EQUIPMENT
AND POSSIBLE INJURY, INCLUDING DEATH MAY RESULT.
2) To postion Red Grip Pull Rod for maintenance purposes, raise the Ball as previousely described. While
pulling the Red Grip Pull Rod at its 45 degree clockwise orientation, and when full extension has been achieved,
and when the Ball is at its full upward travel, rotate the Red Grip Pull Rod an additional 45 degrees clockwise and
release. The handle will remain in its fully extended position. The handle will be oriented at a full 90 degrees
clockwise and pointing towards the front of the truck.
DO NOT HOOK UP TRAILER / DO NOT TOW.
3) In this configuration you can service the Ball and its Receiver Tube from inside the bed. The ball can be
pushed down with your hand, your foot, or any suitable blunt object. While cleaning and lubricating you can cycle
the Ball up and down without leaving the bed. Apply a lubricant when the ball is pushed downward or simply add
lubricant through the Oil holes machined into the Chrome Trim Ring.
4) Once the Ball and Receiver Tube have been serviced and are functioning properly, return to the Pull Rods and
release the Red Grip Pull Rod by rotating 45 degrees counterclockwise. Continue with normal operating
procedures.
5) Lubricate all moving parts once a month. Keep assembly free of dirt and other foreign matter. Use cover
when not in use. Check all fasteners for tightness (
Including Shaft Collar Set-Screws / See Figure 2, Page 2)
before each use. Inspect Ball and all moving parts for wear before each use.
DO NOT TOW TRAILER WITH
WORN OR DAMAGED PARTS.
