GB-1
GB-2
UNPACKING
Remove all packaging from the unit. Retain the packaging. If you
dispose of it please do so according to any local regulations.
The following items are included:
CONTROL PANEL
PRODUCT OVERVIEW
It is normal for the heater to emit some smell and fumes when it is turned
on for the first time or when turned on after not being used for a long
period of time. This smell will disappear when the heater has been turned
on for a short while.
• Before drilling holes ensure that you will not damage any pipes or
wiring hidden in the wall.
• Do not permanently fix the heater to the wall. It is only designed to
hang from the 2 angle brackets that are attached to the wall.
Ensure you unplug your heater from the mains socket and wait for the
heater to cool down completely before cleaning.
GB-3
OVERHEAT PROTECTION
The power to the heater will automatically cut off if the temperature of the
heater exceeds a certain limit. In the event of overheating, the heater will
stop operating. Switch the heater off and allow it to completely cool. The
heater will then resume operating as normal.
WALL MOUNTING (OPTIONAL)
The heater can also be installed on a wall using the supplied accessories.
The feet should not be attached to the heater.
1. Drill 2 holes in the wall. Insert the wall plugs. Make sure the mains cable
can still reach a mains socket.
2. Install 2 angle brackets to the wall using the 4 type B screws.
3. Attach the other 2 angle brackets to the bottom of the heater housing
using the 4 type A screws. These will act as spacers. Do NOT attach
these 2 angle brackets to the wall.
4. Lift up the heater and mount it on to the 2 angle brackets that are
attached to the wall.
ASSEMBLY
Before using the heater, the feet (supplied) must be fitted to the unit.
Attach the feet to the base of the heater using the 4 type A screws provided
(2 for each foot), taking care to ensure that they are located correctly in the
bottom ends of the heaters side moldings.
OPERATION
1. Position the heater upright on the floor away from curtains, furniture or
wallcoverings before plugging your heater into the mains socket.
2. Press the
Power Switches
to the “750W” or “1250W” position. The heater
has 2 built-in heating elements. You can select one or both heating
elements simultaneously.
3. Turn the
Thermostat Control
to the desired position. It is recommended
to select the “MAX” position to get the heater to pre-heat. It will take
5-10 minutes for the heater to fully heat up.
4. When the room reaches the desired temperature, turn the
Thermostat
Control
slowly anti-clockwise until the indicator goes off with a “click”
sound. The heater will temporarily go off.
5. If the room temperature falls below the desired temperature, the heater
and indicator will turn on again until the room temperature reaches the
desired temperature.
CLEANING
Your heater should be cleaned regularly to stop dirt and dust building up
which will affect its performance. Ensure the air inlet and the air outlet are
not blocked.
This can be done with a vacuum cleaner, using the brush attachment.
If items are missing or damaged, please contact Partmaster (UK only).
Tel: 0844 800 3456 for assistance.
The Main Unit
Foot x 2
(P.N.: A007)
Angle Brackets x 4
(P.N.: A008)
The Instruction Manual
(P.N.: C20CHW10-002)
Screws B (30mm) x 4
(P.N.: A003)
Screws A (15mm) x 4
(P.N.: A002)
Wall Plugs x 4
(P.N.: A001)
CONVECTOR HEATER
INSTRUCTION MANUAL
C20CHW10
Thank You
for purchasing your new Currys Essentials
Convector Heater.
We recommend that you spend some time reading this instruction
manual in order to fully understand all the operational features it offers.
Read all the safety instructions carefully before use and keep this
instruction manual for future reference.
Air Inlet
Control Panel
Handle
Air Outlet
MIN
MAX
Power Switches (with Indicators)
750W = Approximately 750W heat output
1250W = Approximately 1250W heat output
750W+1250W = Approximately 2000W heat
output
Thermostat Control
Fit the screws in the
adjacent position
Screw A
at least 600mm
at least 400mm
CEILING
SIDE WALL
GROUND
at least 300mm
Bottom view
Screw B
Screw A
415mm
C
M
Y
CM
MY
CY
CMY
K
C20CHW10_IB_110615.pdf 2 15/06/2011 2:41 PM
