manualshive.com logo in svg

Current Tools 281, Assembly, Operating, Safety And Parts Manual

Share
Download
Current Tools 281 Assembly, Operating, Safety And Parts Manual Download Page 7

7

ASSEMBLY INSTRUCTIONS  

 

— continued

MAJOR COMPONENTS – BENDER

Insert the two 10' lengths of conduit into the remaining leg support assembly and 

tighten the four bolts against the conduit. See Figure 4.
Place the bender mounting unit 15 inches away from the leg support you have just 

completed and tighten the 2 bolts on the bottom of the bender mounting unit against 

the two 10' lengths of rigid conduit to keep the bender mounting unit in place. See 

Figure 4.

Next, attach the two pump 

mounting tracks to the 

bending table with the 4 

conduit clamps as shown 

in Figure 5. DO NOT tighten 

these firmly at this time.
NOTE: Be sure the table is 

level before continuing.

FIGURE 4

FIGURE 5

REMAINING 

LEG SUPPORT 

ASSEMBLY

TIGHTEN THESE BOLTS 

(ONE EACH SIDE)

TIGHTEN 2 BOLTS

EACH SIDE

15"

DO NOT TIGHTEN THESE 

CLAMPS FIRMLY YET

PUMP 

MOUNTING TRACKS

5"

Summary of Contents for 281





























Reviews:

No comments

Brands by name

Popular brands

Load more brands