51
50
Maintenance
• Shut down the device immediately should abnormal operation
be detected.
• Avoid sudden impacts and the product should be dedusted reg-
ularly.
• It is normal for the flash tube to be warm when in use. Avoid
continuous flashes if unnecessary.
• Maintenance of the flash must be performed by our authorized
maintenance department which can provide original accessories.
• Unauthorized service will void the warranty.
• If the product had failures or was wetted, do not use it until it is
repaired by professionals.
• Changes made to the specifications or designs may not be re-
flected in this manual.
FCC Warning
Any Changes or modifications not expressly approved by the par-
ty responsible for compliance could void the user’s authority to
operate the equipment. This device complies with part 15 of the
FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interfer-
ence that may cause undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment. This transmitter must not
be colocated or operating in conjunction with any other antenna
or transmitter.
Declaration of Conformity
CULLMANN GERMANY GmbH herewith declares, that this de-
vice is in compliance with the basic requirements and all other ap-
plicable regulations of the directive 1999/5/EC. You find the decla-
ration of conformity acc. to the R&TTE directive 1999/5/EC under
www.cullmann.de.
Troubleshooting
If there is a problem, refer to this Troubleshooting Guide.
The Camera Flash cannot be charged.
• The battery is installed in the wrong direction.
Install the battery in the correct direction.
• The camera flash’s internal battery is exhausted.
If < > appears and blinks on the LCD panel, replace the bat-
tery immediately.
The Camera Flash does not fire.
• The camera flash is not attached securely to the camera.
Attach the camera’s mounting foot securely to the camera.
• The electrical contacts of the Camera Flash and camera are
dirty.
Clean the contacts.
The power turns off by itself.
• After 90 seconds of idle operation, auto power off took effect if
the flash is set as master
Press the shutter button halfway or press any flash button to
wake up.
• After 60 minutes of idle operation, the flash unit will enter sleep
mode if it is set as slave.
Press any flash button to wake up.
Auto zoom does not work.
• The camera flash is not attached securely to the camera.
Attach the camera flash’s mounting foot to the camera.
The flash exposure is underexposed or overexposed.
• You used high-speed sync.
With high-speed sync, the effective flash range will be short-
er. Make sure the subject is within the effective flash range
displayed.
• You used Manual Flash mode.
Set the flash mode to TTL or modify the flash output.
Photos have dark corners or only parts of the target subject
are illuminated.
• The focal length of lens exceeds the flash coverage.
Check the flash coverage you set. This flash unit has the flash
coverage between 24 and 105mm, which fits medium-format
cameras. Pull the wide panel out to extend the flash coverage.
Compatible Camera Models
This flash unit can be used on the following camera models:
Olympus: E-M10II , E-M5II , E-M1 , E-PL8 , E-PL7 , E-PL6 ,
E-PL5 , E-P5 , E-P3 , PEN-F
Panasonic: DMC-GX85 , DMC-G7 , DMC-GF1 , DMC-LX100 ,
DMC-G85
• This table only lists the tested camera models, not all
Olympus/Panasonic cameras. For the compatibility of
other camera models, a self-test is recommended.
• Rights to modify this table are retained.
•
Note
: With the Panasonic cameras in wireless control
mode, the High-Speed Sync may not sync fire.
FR36_BDA_Olympus 171005.indd 50-51
06.10.2017 15:11:38
