background image

12

PROBLEM

POSSIBLE CAUSE

SUGGESTION

Water does 

not dispense.

Dispenser is unplugged.

Plug the dispenser into a grounded 

GFCI power outlet.

Main power supply is off.

Re-establish main power supply.

The lower cabinet door is open.

Close door and allow time for 

pump to fill the reservoirs.

The water bottle is empty.

Replace water bottle.

(See INITIAL SETUP)

The connection between the water 

bottle cap and the water bottle 

cap connector is not secure.

Properly secure connection.

System has malfunctioned.

Remove water bottle and unplug 

the dispenser. Contact dealer.

Cold water does 

not dispense.

Cooling system switch is OFF.

Turn cooling switch ON.

Too much cold water consumed 

in a short period of time.

Wait 15 minutes for the water to cool.

The ventilation around the

dispenser is insufficient.

Provide at least 6 in (15 cm) of clearance 

on all sides of the dispenser.

System has malfunctioned.

Remove water bottle and unplug 

the dispenser. Contact dealer.

Hot water does 

not dispense.

Hot water switch is OFF.

Turn hot water switch ON.

Too much hot water has been 

consumed in short period of time.

Wait 15 minutes for the water to heat.

System has malfunctioned.

Remove water bottle and unplug 

the dispenser. Contact dealer.

Dispenser is noisy 

during operation.

The dispenser is not level.

Place the dispenser on a level, flat surface.

Dispenser is touching other objects.

Move dispenser away from other objects.

Water leaks from the

water dispense point.

The buttons are stuck down.

Check for foreign objects in the button area.

The water dispense point 

has been damaged.

Contact Culligan Customer Service.

844-787-3148

Water is dripping out 

of the dispenser and 

onto the floor.

The hot tank drain cap is 

not fastened properly.

Tighten the drain cap. 

If the seal inside the drain cap is torn 

or damaged then replace with a new one.

The connection between the water 

bottle cap and the water bottle 

cap connector is not secure.

Properly secure connection.

The hot or cold water tank is leaking.

Remove water bottle and unplug 

the dispenser. Contact dealer.

The water being 

dispensed has 

a strange taste.

This is not uncommon 

with new dispensers.

The taste usually goes away after 

the first bottle has been used.

Dispenser requires cleaning.

Clean the siphon tube and waterways.

(See CLEANING AND MAINTENANCE)

TROUBLESHOOTING  (BOTTLE)

Summary of Contents for BAEMUV1SHSK SSA















Reviews: