background image

Assembly Tip: To avoid scratching grill and to protect floor/patio surfaces, reuse cardboard packaging and lay 
parts on top of while assembling.

STEP 1

-----------------------------------------------------------------------------------

ASSEMBLY INSTRUCTIONS

Some parts may contain sharp edges. Wear protective gloves during assembly and set up. Read and follow 
all safety statements, warnings, assembly instructions and use and care instructions before attempting to 
assemble and use.

Before you Begin: Unpack all the components and verify that everything is present before beginning assembly. 

Several components are packed inside the cooking chamber, it is important to remove these as well.

 

If any part is missing or damaged, DO NOT attempt to assemble the product.

Assembly time: 30 minutes. 

Tools required for assembly: Phillips Head Screwdriver and Gloves (not included). 

ASSEMBLY PREPARATION 

8

•  Attach the Foot Assembly (10) to 

the base of the Body (11) using      
2 pre-installed Screws (A). Repeat 
for other 3 feet.

     

NOTE:

 

Align the corners of the    

     legs with the corner of the 
     Main Body before tightening the  
     screws.

11

10

A

A

x 8

Summary of Contents for CPG-256


























Reviews: