Cubix Xpander Rack Mount 8 4U User Manual Download Page 14 | Manualshive

Page: 14 / 14

background image

Cubix Corporation



2800 Lockheed Way



Carson City, NV 89706-0

713 ● Page 14

Sales 800.829.0550



http://www.cubix.com



[email protected]



xpander-rackmount8-4u-g3 20140317

Issue:

The passively-cooled GPUs or accelerators in Xpander are overheating.

Resolution:

Make sure you have installed blank end brackets (L-brackets) for each empty
Xpander slot. The blank end brackets are essential to assure proper cooling,
especially passively-cooled GPUs (such as NVIDIA Tesla K40) or accelerators
(such as Intel Xeon Phi).

«
...
12
13
14

Summary of Contents for Xpander Rack Mount 8 4U















Reviews:

No comments

Related manuals for Xpander Rack Mount 8 4U

Brand: B-Tech Pages: 24

Terminator WMK Series

Brand: Thermon Pages: 4

Brand: Eagle Group Pages: 4

HA Gasliftarm Single

Brand: HAGOR Pages: 12

Brand: Aigis Mechtronics Pages: 4

Brand: NCR Pages: 15

Brand: nedis Pages: 2

Brand: Wacom Pages: 20

Prima 142-0721-6

Brand: TYPE A Pages: 12

Brand: Husky Mounts Pages: 4

HQ Power HQSS11002

Brand: Velleman Pages: 13

Brand: Crestron Pages: 2

Brand: Crestron Pages: 3

Brand: Crestron Pages: 2

Brand: Crestron Pages: 16

Brand: ShoreStation Pages: 14

Brand: Mount-It! Pages: 9

Brand: Tripp Lite Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands