background image

15

Depress the brake pedal to disengage the cruise 
control and stop the tractor.

Lightly depress the drive pedal.

To change the direction of travel to reverse when 
operating with cruise control, depress the brake pedal 
to disengage the cruise control and bring the tractor to a 
complete stop. Then slowly depress the rear portion of 
the drive pedal with the ball of your foot to travel in 
reverse.

Using the Deck Lift Lever

To raise the cutting deck, move the deck lift lever to the 
left, then place it in the notch best suited for your 
application. Refer to 

Setting The Cutting Height

 earlier in 

this section.

Operating the Headlights

The lamps are ON whenever the ignition key is moved 
out of the STOP position.

The lamps turn OFF when the ignition key is moved to 
the STOP position.

Moving The Tractor Manually

Your tractor’s transmission is equipped with a 
hydrostatic relief valve for occasions when it is 
necessary to move the tractor manually. Opening this 
valve permits the fluid in the transmission to bypass its 
normal route, allowing the rear tires to "freewheel." To 
open the hydrostatic relief valve, proceed as follows:

Locate the hydrostatic bypass rod in the rear of the 
tractor. See Figure 7.

Figure 7

Pull the hydrostatic bypass rod outward, then 
down, to lock it in place.

NOTE: 

The transmission will NOT engage when the

hydrostatic bypass rod is pulled out. Return the rod to
its normal position prior to operating the tractor.

IMPORTANT:

 Never attempt to move the tractor 

manually without first opening the hydrostatic relief 
valve. Doing so will result in serious damage to the 
tractor’s transmission.

Engaging the PTO

Engaging the PTO transfers power to the cutting deck 
or other (separately available) attachments. To engage 
the PTO, proceed as follows:

Move the throttle control lever to the FAST (rabbit) 
position.

Pull the PTO/Blade Engage knob outward into the 
engaged (ON) position. See Figure 8.

Keep the throttle lever in the FAST (rabbit) position 
for the most efficient use of the cutting deck or other 
(separately available) attachments

IMPORTANT:

 The electric PTO clutch will automatically 

shut off if the PTO is engaged with the drive pedal in 
position for reverse travel. Refer to 

Safety Interlock 

Switches

 on page 12.

Figure 8

Hydrostatic

Bypass Rod

ON

OFF

Front View

Top View

PTO

OFF ON

Summary of Contents for SLT1550, SLT1554









































Reviews: