manualshive.com logo in svg

Cub Cadet RZT 17, Service Manual, Page: 17 / 30

Share
Download
Cub Cadet RZT 17 Service Manual Download Page 17

13

10.9. If any electrical connections are present discon-

nect or remove switch from console.                
See Figure 10.9.

NOTE: 

The throttle cable and choke knob does 

not need to be removed. The console can be 
flipped up on the unit and secured safely. 

NOTE: 

There is different throttle and choke 

cable routing for the different models. 

NOTE: 

Not all models have a choke knob.

Figure 10.9

Relays

PTO switch  Key switch

Reverse

switch

Solenoid

11.

BATTERY REMOVAL

The battery can be removed two different ways. 
Depending on the final out come of the work that needs 
to be preformed is which technique you will use. 

When just replacing a battery the fuel pump needs to 
be removed. 

If for any reason the right side control console has to 
be removed in conjunction with removal of the battery, 
the fuel pump will NOT have to be removed.

NOTE: THE FOLLOWING STEPS ARE FOR 
BATTERY REMOVAL WITH OUT THE 
REMOVING THE RIGHT SIDE CONSOLE.

11.1. Disconnect the - (negative) lead to the battery.

11.2. Disconnect the + (positive) lead to the battery.

11.3. Disconnect the battery strap from frame.

11.4. Using a 3/8” wrench remove the two screws 

securing the fuel pump to the engine. The hoses 
don’t need to be removed. See Figure 11.4.

NOTE: 

When reinstalling the battery make sure 

strap is hooked under the seat box before plac-
ing battery in the unit.

11.5. Battery can be pulled up and to the side to 

remove.

NOTE: THE FOLLOWING STEPS ARE FOR 
BATTERY REMOVAL WITH THE REMOVAL 
OF THE RIGHT SIDE CONSOLE.

11.6. Disconnect the - (negative) lead to the battery.

11.7. Disconnect the + (positive) lead to the battery.

11.8. Disconnect the battery strap from frame.

Figure 11.4

Fuel pump

www.mymowerparts.com

K&T Saw Shop 606-678-9623 or 606-561-4983

Summary of Contents for RZT 17































Reviews:

No comments