Cub Cadet RZT 17 Service Manual Download Page 13 | Manualshive

Page: 13 / 30

Cub Cadet RZT 17 Service Manual Download Page 13

9

8.

PIVOT BAR

8.1.

Safely lift and support the front of unit.

8.2.

Disconnect the - (negative) lead to the battery.

8.3.

Using two 9/16” wrenches remove wheel assem-
bly from caster bracket. See Figure 8.3.

NOTE:

Be careful not to drop spacers on both

sides of wheel assembly.

8.4.

Remove center wheel spacer and inspect all
spacers for damage. See Figure 8.4.

NOTE:

Be sure to use a good quality grease

during reassembly.

NOTE:

There are none replaceable 3/4” roller

bearing in the wheel hub.

Figure 8.3

Grease fitting

Figure 8.4

Wheel spacer

.79 x .347
Spacer

8.5.

Lightly grease the wheel spacers during re
assembly. Using a grease gun fill the rest of the
cavity AFTER the wheel assembly has been
mounted.

8.6.

Remove both caster wheel assemblies using a
9/16” wrench. See Figure 8.6.

8.7.

Inspect flange bearing on top and bottom of
pivot axle. Replace if damaged. See Figure 8.7.

NOTE:

Assure proper order during reassembly.

From the top down in this order: hex head cap
screw, lock washer, flat washer, flange bearing,
pivot axle, flange bearing, flat washer, and
caster bracket.

NOTE:

Be sure to use a good quality grease

during reassembly.

Figure 8.6

Caster

wheel

bracket

Figure 8.7

Flat washer

www.mymowerparts.com

K&T Saw Shop 606-678-9623 or 606-561-4983

«
...
11
12
13
14
15
...
»

Summary of Contents for RZT 17































Reviews:

No comments