manualshive.com logo in svg

Cub Cadet 524 SWE, Operator'S Manual

Share
Download
Cub Cadet 524 SWE Operator'S Manual Download Page 18

Apply a light coating of engine oil (or 3-in-1 oil) to the hex 

3. 

shaft. See Fig. 6-3.

NOTE: 

When lubricating the hex shaft, be careful not to get 

any oil on the aluminum drive plate or the rubber friction 

wheel. Doing so will hinder the snow thrower’s drive 

system. Wipe off any excess or spilled oil.

Wheels

At least once a season, remove both wheels. Clean and coat the 

axles with a multipurpose automotive grease before reinstalling 

wheels.

Auger Shaft

At least once a season, remove the shear pins from the auger 

shaft. Spray lubricant inside the shaft and around the spacers and 

the flange bearings found at either end of the shaft. 

See Fig. 6-4.

Figure 6-3

Gear Case

The auger gear case has been filled with grease at the factory. If 

disassembled for any reason, lubricate via the grease fitting with 

two ounces of grease (Part Number 737-0168A).

NOTE: 

To relieve pressure, remove the vent plug before 

lubricating the gear case. See Figure 6-3. Failure to do so could 

result in damage to the gear case seals. 

Augers

Each of the four auger spiral assemblies is secured to the spiral 

shaft with a shear pin and cotter pin. If the auger should strike a 

foreign object or ice jam, the snow thrower is designed so that 

the pins may shear.  

If augers do not turn, check to see if pins have sheared. 

1. 

Replace the pins if needed. Two replacement shear pins 

2. 

and cotter pins have been provided with the snow thrower. 

Spray an oil lubricant into shaft before inserting new pins 

and securing with new cotter pins.

Adjustments

Shift Cable

If the full range of speeds (forward and reverse) cannot be 

achieved, refer to the figures to the right and adjust the shift 

cable as follows:

Place the shift lever in the fastest forward speed position.

1. 

Loosen the hex nut on the shift cable index bracket. See 

2. 

Fig. 6-5.

Pivot the bracket downward to take up slack in the cable. 

3. 

Retighten the hex nut.

4. 

Figure 6-5

Grease Fitting

Spacers

Bow-Tie Pins

Vent Plug

Shear Pins

Figure 6-4

18

s

ectiOn

 6 — M

aintenance

 & a

djustMents

Summary of Contents for 524 SWE

































Reviews:

No comments

Brands by name

Popular brands

Load more brands