Cub Cadet 3X 24 Operator'S Manual Download Page 27

Page: 27 / 28

Attachments & Accessories

The following attachments and accessories are available for your Cub Cadet snow thrower. See your Cub Cadet dealer or the retailer

from which you purchased your snow thrower for information regarding price and availability.

Model Number

Description

929-0071A

Extension Cord, 110V

753-05762A

Heated Grips

OEM-390-679

Drift Cutter Kit

490-241-0032

Snow Cab

490-241-0013

Snow Thrower Auger and Chute Maintenance Kit

490-290-0010

Snow Thrower Cover

490-241-0028

Snow Thrower Tire Chains (16” x 4.8” Tires)

490-241-0029

Snow Thrower Tire Chains (16” x 6.5” Tires)

490-900-0062

Non-Stick Spray

490-240-0011

Fuel Test Swabs

490-850-0008

Siphon Pump

490-000-0028

Carburetor and Choke Cleaner

490-325-0020

32 oz. Tire and Tube Sealant

490-325-0022

16 oz. Tire and Tube Sealant

490-850-0013

Tire/Tube Foot Pump

490-850-0014

Deluxe Tire Plug Kit

22208

8 oz. Fuel Stabilizer

22216

32 oz. Fuel Stabilizer

*Compatible on models equipped with a split alternator.

Summary of Contents for 3X 24





























Search results

Summary of Contents for 3X 24

Reviews:

Related manuals for 3X 24

Brands by name

Popular brands

Cub Cadet 3X 24, Operator'S Manual

Search results

Summary of Contents for 3X 24

Reviews:

Related manuals for 3X 24

Brands by name

Popular brands