Cub Cadet 340 Series Operator'S Manual Download Page 18

The limited warranty set forth below is given by Cub Cadet LLC with 

respect to new merchandise purchased and used in the United States, 

its possessions and territories, and by MTD Products Limited with 

respect to new merchandise purchased and used in Canada and/or its 

territories and possessions.
“Cub Cadet” warrants this product (excluding its

 

Normal Wear Parts

 

as described below) against defects in material and workmanship 

for a period of three (3) years commencing on the date of original 

purchase and will, at its option, repair or replace, free of charge, any 

part found to be defective in materials or workmanship.  This limited 

warranty shall only apply if this product has been operated and 

maintained in accordance with the Operator’s Manual furnished with 

the product, and has not been subject to misuse, abuse, commercial 

use, neglect, accident, improper maintenance, alteration, vandalism, 

theft, fire, water, or damage because of other peril or natural disaster.  

Damage resulting from the installation or use of any part, accessory 

or attachment not approved by Cub Cadet  for use with the product(s) 

covered by this manual will void your warranty as to any resulting 

damage.

Normal Wear Parts 

are warranted to be free from defects in material 

and workmanship for a period of thirty (30) days from the date of 

purchase. Normal wear parts include, but are not limited to items 

such as: batteries, belts, blades, tines, wheels and tires. 

HOW TO OBTAIN SERVICE: 

 Warranty service is available, WITH 

PROOF OF PURCHASE, through your local authorized service 

dealer. To locate the dealer in your area:

In the U.S.A.

To locate the dealer in your area, check your Yellow Pages, or contact 

Cub Cadet LLC at P.O. Box 361131, Cleveland, Ohio 44136-0019, or 

call 1-877-282-8684,  or log on to our Web site at www.cubcadet.

com.

In Canada

Contact MTD Products Limited, Kitchener, ON N2G 4J1, or call 

1-800-668-1238 or log on to our Web site at www.mtdcanada.

com.
This limited warranty does not provide coverage in the following 

cases:
a.  The engine or component parts thereof. These items may  

carry a separate manufacturer’s warranty. Refer to applicable 

manufacturer’s warranty for terms  and conditions.

b.  Routine maintenance items such as lubricants, filters, blade 

sharpening, tune-ups, brake adjustments, clutch adjustments, 

deck adjustments, and normal deterioration of the exterior finish 

due to use or exposure.

c.  Cub Cadet does not extend any warranty for products sold or 

exported outside of the United States and/or Canada, and their 

respective possessions and territories, except those sold through 

Cub Cadet’s authorized channels of export distribution.

d.  Replacement parts that are not genuine Cub Cadet parts.
e.  Service completed by someone other than an authorized service 

dealer.

f.  Transportation charges and service calls.
g.  Cub Cadet does not warrant this product for commercial use.

No implied warranty, including any implied warranty of 

merchantability of fitness for a particular purpose, applies after 

the applicable period of express written warranty above as to the 

parts as identified. No other express warranty, whether written or 

oral, except as mentioned above, given by any person or entity, 

including a dealer or retailer, with respect to any product, shall 

bind Cub Cadet.  During the period of the warranty, the exclusive 

remedy is repair or replacement of the product as set forth above.
The provisions as set forth in this warranty provide the sole and 

exclusive remedy arising from the sale.  Cub Cadet shall not be 

liable for incidental or consequential loss or damage including, 

without limitation, expenses incurred for substitute or replacement 

lawn care services or for rental expenses to temporarily replace a 

warranted product.

Some states do not allow the exclusion or limitation of incidental 

or consequential damages, or limitations on how long an implied 

warranty lasts, so the above exclusions or limitations may not apply 

to you.
In no event shall recovery of any kind be greater than the amount of 

the purchase price of the product sold.  

Alteration of safety features of 

the product shall void this warranty. 

 You assume the risk and liability 

for loss, damage, or injury to you and your property and/or to others 

and their property arising out of the misuse or inability to use the 

product.
This limited warranty shall not extend to anyone other than the 

original purchaser or to the person for whom it was purchased as a 

gift.

HOW STATE LAW RELATES TO THIS WARRANTY: 

 This limited 

warranty gives you specific legal rights, and you may also have other 

rights that vary in different jurisdictions.

IMPORTANT:  

Owner must present Original Proof of Purchase to 

obtain warranty coverage.

    Cub Cadet LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019; Phone: 1-877-282-8684

          MTD Canada Limited - KITCHENER, ON N2G 4J1; Phone 1-800-668-1238

GDOC-100087 REV. A

CUB CADET LLC

MANUFACTURER’S LIMITED WARRANTY FOR 

EDGERS, STRING TRIMMERS & TILLERS 

Summary of Contents for 340 Series





































Reviews: