Cub Cadet 28HP Tank 53AB5JEZ630 Operator'S And Service Manual Download Page 10

10

OPERATING INSTRUCTIONS

Figure. 1

Figure. 2

Ignition Switch

Electric Blade
Clutch Switch

Hour Meter
(tach optional)

Engine throttle

Glow Plug

indicator lights

Parking Brake

A.General

1.

When Mowing:

a.

Keep adults, children, and pets away from 
the area to be mowed.

b.

When operating this mower, in the forward 
direction, do not allow the steering levers 
to return to Neutral on their own. Always 
maintain a firm grip on the levers, operate 
them smoothly and avoid any sudden 
movements of the levers when starting and 
stopping.

c.

If the mower is equipped for side dis-
charge, never use the mower without the 
discharge chute installed and placed in the 
down position.

d.

Always remove debris and other objects 
from the area to be mowed (Note: debris 
and loose grass will reduce traction).

e.

Mow only in daylight.

f.

Watch for holes, sprinkler heads, and other 
hidden hazards.

g.

Avoid driving too close to trees, creeks, 
ditches, sand traps, and other obstacles.

h.

Before backing up, check behind and 
watch where you are going.

i.

Always reduce speed when making a turn, 
and when grass is wet.

j.

Always mow across slopes, never up and 
down the slope. Do not operate on steep 
slopes and slow down before turning. 
Avoid turning downhill if possible, start at 
the bottom and work up to the top. Use 
extra care and go slowly when turning 
downhill. Control the speed and direction 
of the zero turn machine “primarily” with 
the speed/directional control (lap bar) of 
the downhill side of the machine...I.E., 
maintain the uphill side lap bar “essen-
tially” in a fixed position.

k.

Be careful when crossing gravel paths or 
roadways. Always turn off the blade clutch 
switch and wait until the blades stop rotat-
ing and raise the cutting deck to the trans-
port position. Always allow other vehicles 
to have the right of way.

l.

If you hit a solid object while mowing, turn 
off the blade clutch switch, place the steer-
ing levers in the neutral position, move the 
throttle to slow, set the parking brake, shut 
off the engine, and take the key from the 
ignition switch. Inspect for damage. Repair 
the damage. Make sure the blades are in 
good condition and that the blade bolts are 
tight before restarting the engine.

m. Never leave the mower unattended without 

observing the following: turn off the blade 
clutch switch, placing the steering levers in 
the neutral position, moving the throttle to 
slow, setting the parking brake, shutting off 
the engine and taking the key from the igni-
tion switch.

n.

Never walk or stand on the discharge side 
of the mower when the engine is running. 
Turn off the blade clutch switch if another 
person approaches while you are operat-
ing the mower.

o.

Never attempt to operate the traction unit 
without having the mowing deck attached.

p.

Keep the mower and especially the engine 

and hydraulic components clean and free 

Summary of Contents for 28HP Tank 53AB5JEZ630





































Reviews: