background image

  

 

Operation 

VA 525 EN  V1.01 

 

page 

37

 o 

41

 

 

10.4 

MBus 

Settings 

 MBus 

 

 

 

 

 

 

10.4.1  Default Settings communication  

 

 

Primary Adress*:  

ID:  

 

 

Serialnumber of Sensor 

Baud rate*: 

 

2400 

Medium*: 

 

depending on medium (Gas or Compressed Air) 

Manufacturer ID: 

CSI 

VIF coding: 

 

Primary VIF 

 

 

Both addresses, Primary address and ID, could be automatic searched in the M-Bus system. 

 

10.4.2  Default values transmitted 

 

Value 1 with [Unit]*: 

 

Consumption [m³] 

Value 2 with [Unit]*: 

 

Flow [m³/h]Consumption [m³] 

Value 3 with [Unit]*: 

 

Gas temperature [°C] 

 

*

All Values could be changed / preset in production or with CS Service software (Order-No. 0554 2007) 

 

 

 
The Sensor offers two possibilities for coding the 
Value Informaition Field (VIF). 
 

 

Primary VIF (The units and multiplier  
correspond to  MBus specification 4.8 
chapter 8.4.3 

 

Plain text VIF ((units are transmitted as 
ASCCII characters. So units that are not 
included in MBus specification chapter 8.4.3 
are possible  

 
Switch to  Plain Text VIF by activation of 

„Units as 

String“.

 

Summary of Contents for VA 525










































Reviews: