manualshive.com logo in svg

CS Instruments VA 525, Instruction Manual, Page: 20 / 41

Share
Download
CS Instruments VA 525 Instruction Manual Download Page 20

  

 

Operation 

VA 525 EN  V1.01 

 

page 

20

 o 

41

 

 

10.3.1.4  Advanced settings 

Setup 

  Sensor Setup

 Advanced

 

 

 

 

 

10.3.1.4.1  Definition of the reference conditions 

Here can be defined the desired measured media reference conditions for pressure and temperature 

and times for the filter and averaging.

 

 

 

Factory presetting for reference temperature and reference pressure are  20 °C, 1000 hPa 

 

All volume flow values (m³/h) and consumption values indicated in the display are  

related to 20 °C and 1000 hPa (according to ISO 1217 intake condition) 

 

Alternatively 0 °C and 1013 hPa (=standard cubic meter) can also be entered as a reference.  

 

Do not enter the operation pressure or the operation temperature under reference conditions

!

 

 
 
Setup 

  Sensor Setup

 Advanced 

 Ref. Settings 

 

 

 

 

 

To make changes, first select a menu with 
button 

„

“

 and confirm selection by pressing 

„OK“ 

. 

 

Duc 

Volume Type 

Summary of Contents for VA 525










































Reviews:

No comments