Crystal Vision Indigo ADP 310 User Manual Download Page 21

Page: 21 / 49

Crystal Vision

Control and Status monitoring

Menu Structure

The basic menu structure for card edge, front panel access and VisionWeb is
identical and consists of the following groups and sub-groups.

Note that some of

these groups and sub-groups will change according to the piggyback boards
fitted – for example, references to AES will only appear if DIOP4 piggybacks are
fitted:

Status

Reference Status

Reference Present

Reference Standard

Sub PCB Type

Front

Rear

Audio Settings

Delays, Invert &

Mono

AES Audio Ip

Present

Silent

Invert

Mono

User Delay

PCM Audio

Aip Audio Input

Present

Silent

Invert

User Delay

Audio Gain

Channel Gain

Select Channels

Gain 1

Gain 2

Gain 3

Gain 4

Cal. Audio Gain

AES Output Router
(only if DIOP4
piggybacks fitted)

Audio Op Channels

Present

Mute

Take

AOP Output Router
(only if 3G-
AIP2/AOP2
piggybacks fitted)

Audio Op Channels

Present

Mute

Take

Presets, Reset &

GPO’s

Presets

Store/Recall

Preset Select

Store

ADP 310 User Manual R1.2

19 June 2019

Summary of Contents for Indigo ADP 310


















































Search results

Summary of Contents for Indigo ADP 310

Reviews:

Brands by name

Popular brands

Crystal Vision Indigo ADP 310, User Manual

Search results

Summary of Contents for Indigo ADP 310

Reviews:

Brands by name

Popular brands