Crystal Vision CoCo104 User Manual Download Page 61

Page: 61 / 61

Crystal Vision

Specification

CoCo104 User Manual R2.0

26/09/05

Ordering
information

CoCo104

Colour correction and legaliser

CoCo Controller

Dedicated 1U control panel

RM01

Single slot frame rear module

Statesman

PC Control System

Indigo 4

4U frame with passive front panel for up to 24 modules

Indigo 2

2U frame with passive front panel for up to 12 modules

Indigo 1

1U frame with passive front panel for up to 6 modules

Indigo DT

Desk top box with passive front panel for up to 2 modules

Indigo 2A

2U frame, Statesman enabled with active control panel for up 12 modules

Indigo 1A

1U frame, Statesman enabled with active control panel for up 6 modules

Indigo DTA

Desk top box, Statesman enabled with active control panel for up 2 modules

Indigo 4S

4U frame with passive front panel fitted with Statesman CPU for up to 24
modules

Indigo 2S

2U frame with passive front panel fitted with Statesman CPU for up to 12
modules

Indigo 1S

1U frame with passive front panel fitted with Statesman CPU for up to 6
modules

Indigo DTS

Desk top box with passive front panel fitted with Statesman CPU for up to 2
modules

Indigo 2-48V

48V 2U frame with passive front panel for up to 12 modules

Indigo 1-48V

48V 1U frame with passive front panel for up to 6 modules

Indigo 2A-48V

48V 2U frame, Statesman enabled, with active control panel for up 12 modules

Indigo 1A-48V

48V 1U frame, Statesman enabled, with active control panel for up 6 modules

Indigo 2S-48V

48V 2U frame with passive front panel fitted with Statesman CPU for up to 12
modules

Indigo 1S-48V

48V 1U frame with passive front panel fitted with Statesman CPU for up to 6
modules

Indigo 2

2U frame without active control panel for up to 12 modules

Indigo 1

1U frame without active control panel for up to 6 modules

Indigo DT

1U Desk top box without active control panel for up to 2 modules

Indigo 2A

2U frame with active control panel for up to 12 modules

Indigo 1A

1U frame with active control panel for up to 6 modules

Indigo DTA

1U Desk top box with active control panel for up to 2 modules

Indigo 2S

Statesman enabled only 2U frame for up to 12 modules

Indigo 1S

Statesman enabled only 1U frame for up to 6 modules

Indigo DTS

Statesman enabled only 1U desk top box for up to 2 modules

Summary of Contents for CoCo104






























































Search results

Summary of Contents for CoCo104

Reviews:

Related manuals for CoCo104

Brands by name

Popular brands

Crystal Vision CoCo104, User Manual

Search results

Summary of Contents for CoCo104

Reviews:

Related manuals for CoCo104

Brands by name

Popular brands