CRUX GMLAN ONSTAR
BACK UP CAMERA
USING THE MUTE CIRCUIT BOARD (FIG 1)
The external mute circuit is used to mute the audio on your radio.
Determine whether your radio is equipped with BOSE, then place
the 8 pin connector into the proper female connector. Reference the
sticker on the mute circuit board.
RADIO REMOTE SELECT:
0. Pioneer
1. Alpine
2. Clarion
3. Kenwood
4. JVC
5. Sony/Jensen/Dual
TO FACTORY
HARNESS
24-PIN
(male plug)
AFTERMARKET
RADIO
MATCH LOOSEWIRES TO AFTERMARKET RADIO
front left speakers
front right speakers
rear left speakers
rear right speakers
constant
accessory
ground
illumination
amp on
vss
swc
8-PIN
(male plug)
12-PIN
(male plug)
INTERFACE
THIS HARNESS ONLY HAS
3-PINS POPULATED.
DO NOT PLUG IN THE
FULLY POPULATED 8-PIN.
16-PIN
(male plug)
14-PIN
(male plug)
8-PIN
(male plug)
MUTE
CIRCUIT
BOARD
(SEE FIG 1)
Black
= Ground
Red
= Accessory
Yellow
= Constant
Orange
= Illumination
Blue/White
= Amplifier Turn-On
White
= Left Front (+)
White/Black
= Left Front (-)
Gray
= Right Front (+)
Gray/Black
= Right Front (-)
Green
= Left Rear (+)
Green/Black
= Left Rear (-)
Purple
= Right Rear (+)
Purple/Black
= Right Rear (-)
Purple/White
= Vehicle Speed Sense
Blue/Yellow
= SWC (Kenwood/ JVC)
Orange/White
= Dimmer
Yellow/Black
= Parking Brake
Red/White
= Reverse Gear
We recommend reading this installation guide first before starting any
work. Following these instructions from “Start” to” Finish” will ensure
a smooth and hassle free installation. We offer telephone support M-F
9:00 AM – 5:00PM PDT at 1 (855) 822-1348. We are here to help.
PARTS INCLUDED:
(1) Interface Module
(1) GM 29-Bit Harness (Part Number: Crux2513)
(1) Instruction Sheet
(1) Reverse Camera Harness (CJA2103A)
PRECAUTIONS:
- Remove the negative side of the battery to avoid any short circuits
durring the installation.
- Do not install the interface near any major components or near the
HVAC system. This may cause damage or overheating to the vehicle.
PRELIMINARY:
Please read the entire mannual before installing this interface.
This unit provides the following:
- 12V Acc Output (3A Max/ RAP)
- Illumination Output (250mA Max)
- Low Voltage (Batt Run-Down Protection)
Chimes Include:
- Seatbelt
- Check Engine
- Key In Ignition
- Low Fuel
- Low Oil
- Lights On
Before installing this interface please review the options before
removing the factory radio. Some options may need to be adjusted
prior to removing the factory radio. Options include:
- Standard BOSE Amplifier
- Premium Bose (Y-91)
ONSTAR RADIO REPLACEMENT FOR SELECT GM LAN 29-BIT VEHICLES 2006-UP
SOOGM-16
SOOGM-16A
Harness: 2606 Only.
Covers 2012-UP Pick-Ups
w/ Navigation listed below.
WIRING COLOR CODES
The module has been rated for upto 3A max of output.
For applications demanding a continuous output of 3A or more,
we reccomend using a standard BOSCH (SPDT) relay.
See your local car audio specialist.
OVERVIEW OF INSTALLATION
CONNECT THE WIRES,
COLOR FOR COLOR.
IMPORTANT:
- The Front and Rear fading are not retained on Y-91 BOSE.
- The Onstar volume output is defaulted to low-gain
BUICK:
2008 - 2012 Enclave
2006 - 2011 Lucerne
CADILLAC
2006 - 2010 DTS
2007 - 2013 Escalade
2007 - 2009 SRX
CHEVROLET:
2007 - 2013 Avalanche*
2007 - 2009 Equinox
2008 - 2011 Express Van
2006 - 2013 Impala/ Impala SS
2006 - 2007 Monte Carlo
2007 - 2013 Silverado* 1500-3500 Pickup
2007 - 2013 Suburban*
2007 - 2013 Tahoe*
2009 - 2012 Traverse
GMC:
2007 - 2012 Acadia
2008 - 2011 Savana
2007 - 2013 Sierra 1500-3500 Pickup*
2007 - 2013 Yukon*
HUMMER:
2008 - 2009 H2
PONTIAC:
2007 - 2009 Torrent
SATURN:
2007 - 2009 Outlook
2008 - 2009 Vue
SUZUKI:
2007 - 2008 XL7
*2012 Vehicles with Navigation Units are not
supported. Needed is SOOGM-16A
Tech Tip:
Make sure to wipe the 3.5mm plug
before inserting into the aftermarket radio
to avoid a bad connection.
This Interface Supports:
- BOSE Amplifier
- Y-91 System
- Rear Seat Entertainment*
- Back-Up Camera
USING THE SWC WIRE ON NEW JVC UNITS
New JVC units no longer carry the 3.5mm cable and have added the
SWC signal via a Lt. Blue/Yellow wire.
This wire needs to be connected to the SWC wire labeled “Kenwood”
also Lt. Blue/Yellow. Be sure to keep the dial switch set to number 4
when using JVC units.
Use a small screw
driver to make
adjustments.
Note: Seek Up is not
supported on Jensen
radios.
ADJUSTING THE GAIN
High Gain (Non-Bose Systems)
Press OnStar button, Heear “Onstar Ready“, Turn Dial knob to “9“,
Wait 4 seconds, Press Onstar button “Thank you Good Bye“.
Turn Dial knob back to Aftermarket radio corresponding.
The insterface is defaulted at Low-Gain.(BOSE Systems)
Rev. 082113
REAR SEAT ENTERTAINMENT (SPECIAL ORDER)
1. Conect the rear seat entertainment 16-Pin connector to the vehicles
16-Pin factory connector.
2. Connect the RCA’s to the aftermarket radio video and audio input.
3. Test the video and audio before installing the radio into the dash.
Must Special Order Harness: CJA2333A
CRU
X
G
M
LA
N
O
N
STA
R
TO
OV
E
R
H
EAD
S
C
R
EEN
A
U
X
A/
V
GRAY
Connector
Connect to
Ground
BACK-UP CAMERA CONNECTION
1. Conect the back-up camera 16-Pin connector to the vehicles 16-Pin
factory connector.
2. Connect the yellow video RCA to the new aftermarket radio video input.
3. Test the video feed before installing the radio back into the dashboard.
8-PIN
(male plug)
BOSE
Non-BOSE
Part Number:
CJA2103A
INTERFACING SOLUTIONS
