background image

REAR PANEL 

 

 

 

1.

 

ANTENNA :

 This jack accepts 50 ohms coaxial cable with a PL-259 type plug. 

 

2.

 

DC POWER :

 This accepts 13.8V DC power cable with built-in fuse. The power 

cord provided with the radio has a black and red wire. The black goes to negative 
and red goes to positive.  

 

 

3.

 

EXT. SP :

 This jack accepts 4 to 8 ohms, 5 watts external speaker. When the 

external speaker is connected to this jack, the built-in speaker will be disabled. 

 

4.

 

CW. KEY :

 This jack is for Morse Code operation. To operate, connect a CW Key 

to this jack and place the Mode Control in the CW position. 

 

 

PROCEDURE TO RECEIVE AND TRANSMIT 

 

A.

 

MICROPHONE 

The receiver and transmitter are controlled by the push-to-talk switch on the 

microphone. Press the switch and the transmitter is activated, release switch to receive. 
When transmitting, hold the microphone two inches from the mouth and speak clearly 
in a normal voice. This transceiver comes complete with a low impedance dynamic 
microphone.  
 

B.

 

PROCEDURE TO RECEIVE 

1.

 

Be sure that power source, microphone and antenna are connected to the proper 
connectors before going to the next step. 

 
2.

 

Turn 

VOL

 knob clockwise to apply power to the radio.  

 
3.

 

Set the 

VOL

 for a comfortable listening level. 

 
4.

 

Set the 

MODE

 switch to the desired mode.   

 
5.

 

Listen to the background noise from the speaker. Turn the 

SQ

 knob slowly 

clockwise until the noise just disappears. The 

SQ

 is now properly adjusted. The 

receiver will remain quiet until a signal is actually received. Do not advance the 
control too far or some of weaker signals will not be heard. 

 
6.

 

Set the 

CHANNEL

 selector switch to the desired channel. 

 
7.

 

Set the 

RF GAIN

 control fully clockwise for maximum RF gain. 

 
8.

 

Adjust the 

FINE/COARSE

 control to clarify the SSB/CW signals or to optimize 

AM/FM signals. 

 

C.

 

PROCEDURE TO TANSMIT 

1.

 

Select the desired channel of transmission 

 
2.

 

Set the 

MIC GAIN

 control fully clockwise. 

 
3.

 

If the channel is clear, depress the push-to-talk switch on the microphone and speak 
in a normal voice. 

 
 
 
 

11

10

- DC 13,8V +

Summary of Contents for SuperStar












Reviews: