Crown CT31012, Original Instructions Manual, Page: 26 / 168

26
English
power tool, if they are not supervised or instructed
about use of the power tool by a person responsible
for their safety�
• Do not force the power tool. Use the correct
power tool for your application
� The correct power
tool will do the job better and safer at the rate for which
it was designed�
• Do not use the power tool if the switch does
not turn it on and off.
Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired�
• Disconnect the plug from the power source and /
or the battery pack from the power tool before mak-
ing any adjustments, changing accessories, or
storing power tools
� Such preventive safety meas-
ures reduce the risk of starting the power tool acciden-
tally�
•
Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool.
Power tools are dangerous in the hands
of untrained users�
•
Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool’s op-
eration. If damaged, have the power tool repaired
before use.
Many accidents are caused by poorly
maintained power tools�
• Keep cutting tools sharp and clean.
Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control�
• Use the power tool, accessories and tool bits
etc. in accordance with these instructions, taking
into account the working conditions and the work
to be performed.
Use of the power tool for operations
different from those intended could result in a hazard-
ous situation�
• Keep handles and grasping surfaces dry, clean
and free from oil and grease.
Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations�
•
Note that when you operate a power tool, please
hold the auxiliary handle correctly, which is helpful
when controlling the power tool� Therefore, proper
holding can reduce the risk of accidents or injuries�
Service
•
Have your power tool serviced by a qualified
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool
is maintained�
•
Follow instruction for lubricating and changing ac-
cessories�
Safety guidelines during power tool
operation
Before commencing operation
• Spraying inflammable materials increases the risk of
fire or explosion, so please follow all the required pre
-
cautions and ensure that there are fire-extinguishing
means on site�
• After handling inflammable materials (for example,
after mixing or thinning paint or after cleaning any parts
of the power tool) remove all used containers and the
cloth, as they may cause fire.
•
Make sure that the area where the works will take
place is properly ventilated - gases or vapors gener-
ated during work may be harmful to your health and
increase the risk of fire or explosion.
• Do not work near the sources of open fire or sparks,
hot objects, engines�
• Do not spray materials having a flash point
below 21°С - this increases the risk of fire or explosion.
•
Prior to spraying the material, carefully read manu-
facturer's instructions in order to undertake the appro-
priate safety measures�
•
Do not spray unknown materials or materials with
unknown dangers�
•
Do not spray any materials that can damage the
power tool; if the power tool breaks as a result, your
warranty will be voided� Spraying acids, alkalis, materi-
als containing abrasive particles, materials containing
lead, liquid glass, excessively thick materials, and oth-
er materials that are difficult to spray or to form drops
is strictly prohibited�
•
Install the power unit onto the horizontal vibration-
free surface� The air sucked through the holes of the
covers
12
must be clean; therefore, do not use the
base unit in a dusty environment; also make sure that
the covers
12
are not covered by anything (only for
models
CT31014, CT31014M, CT31015
)�
During operation
•
Use personal protective equipment - special cloth-
ing, glasses, gloves, and closed shoes�
•
Use special masks intended for the protection of
respiratory system from harmful substance vapors�
Please note! The use of dust masks or respirators
will not assure the required effect - you may suffer
severe intoxication.
• Smoking during spraying inflammable materials is
strictly prohibited�
•
While working, do not direct the stream of the
sprayed material onto yourself, other individuals,
or animals� The stream may pierce your skin (even
through gloves) and inject the sprayed material - in
such a case seek medical attention immediately�
•
Please bear in mind that during working the sur-
rounding air fills with "mist" consisting of fine drop
-
lets of the sprayed material that subsequently settles
on surrounding surfaces� The surfaces on which the
"mist" precipitation is unwanted should be covered�
When working outside, the "mist" is exposed to wind,
which may lead to negative consequences (unwanted
painting of objects, causing harm to health, environ-
mental contamination)�
•
Do not switch on the power tool if there is no liquid in
the reservoir - dry running causes rapid wear of power
tool components�
After finishing operation
•
The power tool must be cleaned after each use as
described below� Failure to clean or improper cleaning
may cause breakage of the power tool, which will void
the warranty�
•
Dispose of the sprayed material residues (paint
materials, solvents, etc�) in strict compliance with the
manufacturer's instructions�