Crown CT26010HX, Original Instructions Manual

Page: 24 / 180

24
English
• When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal to
another. Shorting the battery terminals together may
cause burns or a fire.
• Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact acci-
dentally occurs, flush with water. If liquid contacts
eyes, additionally seek medical help. Liquid ejected
from the battery may cause irritation or burns�
• Avoid unintentional switching on. Ensure the
on / off switch is in the off position before inserting
battery pack. Carrying the power tool with your finger
on the on / off switch or inserting the battery pack into
power tools that have the switch in accidents�
•
Do not open the battery.
Danger of circuit�
•
In case of damage and improper use of the bat-
tery, vapors may be emitted. Provide for fresh air
and seek medical help in case of complaints. The
vapors can irritate the respiratory system�
• When the battery is defective, liquid can escape
and come into contact with adjacent components �
Check any parts concerned� Clean such parts or re-
place them, if required�
• Protect the battery against heat, e.g., also
against continuous sun irradiation and fire. There
is danger of explosion�
WARNING! Read all safety warnings and
all instructions.
• Protect the battery charger from rain and mois-
ture. The penetration of water in a battery charger in-
creases the risk of electric shock�
• Do not charge other batteries. The battery charger
is suitable only for charging lithium ion batteries within
the listed voltage range� Otherwise there is danger of
fire and explosion.
• Keep the battery charger clean. Contamination
may cause the danger of electric shock�
•
Check the battery charger, cable and plug each
time before using. Do not use the battery charger
when defects are detected. Do not open the battery
charger yourself and have it repaired only by quali-
fied personnel using original spare parts. Damaged
battery chargers, cables and plugs increase the risk of
electric shock�
• Do not operate the battery charger on easily in-
flammable surfaces (e.g. , paper , textiles , etc.) or
in combustible environments. There is danger of fire
due to the heating of the battery charger during charging�
Service
• Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power tool
is maintained�
• Follow instruction for lubricating and changing ac-
cessories�
Special safety warnings
• Before work, inspection shall be carried out to
see whether the milling cutter is installed; you
should firmly hold the machine during work. Milling
cutter with appropriate dimension shall be used.
Anytime when the milling cutter is used or changed, it
must be ensured that switch on the machine is on off
position� In order to avoid personal injury done to you
and your bystanders, the power lines must be pulled
out of the socket when the milling cutter is assembled
or changed�
• When the machine is used, you will work in dusty
environment; therefore, you should wear mask and
goggles. If you have long hair, you shall wear hair care
cap� You shall not wear loose clothes during work�
• Before the machine is removed from the work-
piece, you shall cut off power switch and com-
pletely stop the milling cutter.
• The hands shall always be far away from the ro-
tating parts. When the milling cutter is in contact with
the workpiece, you shall not make an attempt to start
the machine�
• After work, the switch shall be turned off first
and then lock knot of guide pillar shall be loosed
to make the machine return to original position.
Safety guidelines during power tool
operation
Before commencing operation
• During machining, do not place the workpiece on
a sturdy surface (concrete, steel, stone, etc�) - when
the router bit passes through the workpiece, you can
damage the router bit and lose control over the power
tool�
• Use the router bits whose allowable rotary speed
does not exceed the rotary speed of the power tool
spindle� Observe manufacturer's recommendations
for router bits use� Do not use router bits that do not
conform to the specifications included in the user's
manual�
• Use only sharp nondefective router bits� Bended,
blunt or cracked router bits must be replaced�
• The router bit shank diameter must match precisely
with the internal diameter of the power tool collet�
• Never use the router bit if its cutting unit diameter
exceeds the diameter of the hole in the base plate�
• Remove all nails or any other metal objects from
blanks before cutting�
•
When making cuts in walls or partitions, it is nec-
essary to find the location of hidden wiring, water-
pipes and gas pipes� Severe injuries may occur as a
result of damaging electric wiring or household utility
lines�
During operation
• Keep your hands at a safe distance from the rotat-
ing router bit� Remember that when machining a work-
piece, the router bit end occasionally protrudes beyond
the lower part of the workpiece and is not protected -
touching it may cause severe injuries� Never touch the
rotating router bit with your hands�
• Never start the machining until the router bit reaches
its full speed�
• Advance the router bit to the workpiece only with the
power tool turned on, otherwise the router bit may be
pinched in a workpiece, or a recoil and loss of control
over the power tool can occur�
• When processing small blanks, use clamping devic-
es. If the blanks are too small to be fixed properly - do
not process them�