Crown CT24001HX, Original Instructions Manual, Page: 27 / 180

27
English
Symbol Meaning
Caution! Possible injury from
sharp edges of a cutting ac-
cessory�
Do not dispose of the power
tool in a domestic waste
container�
Power tool designation
The cordless power planer is designed for planing,
edge cutting, grooving of wood and wood materials�
Power tool components
1 Junction pipe
2 Chip ejection direction switch
3
Lock-off button
4 On / off switch
5 Protective casing
6 Ventilation slots
7 Battery lock *
8 Indicators of the state of battery charge *
9 Control button of the state of battery charge *
10
Battery *
11 Additional handle with regulator for planing depth
adjustment
12 Planing depth setting scale
13 Front base plate
14 V-groove
15 Safety stop
16
Back base plate
17 Accessories storage compartment
18 Charger *
19 Dust bag *
20
Allen key *
21 Wrench *
22 Accesories storage container *
23 Vertical stop *
24 Cup head square shoulder bolt *
25 Bracket *
26 Winged nut *
27
Thrust plate *
28 Wing screw *
29 Side stop (assembly) *
30 Indicator (green) *
31 Indicator (red) *
32 Charger label *
33 Clamping bolt *
34
Drum
35 Interchangeable blades *
36 Fastening plate
37 Adjusting bolt
38
Adjusting plate for interchangeable blade
39 Driving belt *
40 Driven pulley
41 Drive pulley
42 Housing screw
* Optional extra
Not all of the accessories illustrated or described
are included as standard delivery.
Installation and regulation of power tool
elements
Before carrying out any works on the power tool
remove the battery 10.
Do not draw up the fastening elements
too tight to avoid damaging the thread.
Storage of accessories (see fig. 1)
•
Remove container 22 from compartment 17 (see
fig. 1.1).
• Remove keys 20 and 21 from container 22 (see
fig. 1.2).
• After completing the adjustment work, it is recom-
mended to fold the keys 20 and 21 into the contain-
er 22 , and insert it into the compartment 17 �
Installation / dismantling of the side stop (see fig. 2)
•
Assembly side stop 29 as it is shown in fig. 2.1.
• Install the side stop 29 using the wing screw 28 (see
fig. 2.2).
• Disassembly operations do in reverse sequence�
Setting of grooving width (see fig. 3)
• Loosen the winged nut 26 of the side stop 29 , and
set the necessary width of grooving by moving the
thrust plate
27
(see fig. 3).
•
Tighten the winged nut 26 �
Installation / dismantling of the vertical stop (see
fig. 4.1)
• Install the vertical stop 23 using the wing screw 28
(see fig. 4.1).
• When dismantling the vertical stop 23 unscrew the
wing screw 28 �
Setting of grooving depth (see fig. 4.2)
• Loosen the wing screw 28 of the vertical stop 23 and
set the desired depth of grooving (see fig. 4.2).
• Tighten the wing screw
28
�
Changing the direction of chips ejection (see fig. 5)
To change the direction of chips ejection move switch 2
as shown in figures 5.1 or 5.2.
Dust bag (see fig. 6)
Install the dust bag 19 on the junction pipe 1 (see
fig. 6).
Attention: when installing the dust bag 19,
the direction of the chips ejection must be taken
into account.
Charging procedure of the power tool
battery
Initial operating of the power tool
The power tool is supplied with a partially charged
battery 10. Before the first use, the battery 10 must
be fully charged.