INSTALLATION INSTRUCTIONS
S W A N 1 0 0 0
PASSIVE INFRARED & MICROWAVE DETECTOR With PET IMMUNITY
SETTING UP THE DETECTOR
LED INDICATION OF ALARM SIGNAL
Switch 1
of dipswitch
DIP-5 use for setting -
LED
Enable / Disable
Position Up – ON
- LED ENABLE
The RED LED will activate when the detector
is in alarm condition.
Position Down – OFF
- LED DISABLE
The LEDS are disabled.
Note:
the state of the switch “LED” does not affect the
operation of the relay.
When an intrusion is detected, the LED will activate
and the alarm relay will switch into alarm condition for 2
sec.
LED
INDICATORS:
YELLOW LED - MW detection’s
GREEN LED - PIR detection’s
RED LED - Alarm
PIR SENSITIVITY ADJUSTMENT
Switch 2
of dipswitch DIP5 use for setting the PULSE
count function in order to provide PIR sensitivity control
according to the environment.
Position Down – OFF – High sensitivity
For stable environments.
Position Up – ON – Low sensitivity
For harsh environments.
MW SENSITIVITY ADJUSTMENT
Switch 3
of dipswitch DIP5 use for setting the MW
function in order to provide MW sensitivity control
according to the environment.
Position Down – OFF – High sensitivity
For normal operation – immediate detection.
Position Up – ON – Low sensitivity
For harsh environments.
PET IMMUNITY SETTING
Switch 4
of dipswitch DIP5 use for setting the PET
Immune function - Up to 15Kg or 25Kg, depending on
the pet weight.
Position Up - ON
Immunity to an animal up to 15 kg
Position Down - OFF
Immunity to an animal up to 25 kg
ALARM MODE SETTING
Switch 5 of dipswitch DIP5 use for setting the mode of
the detector.
Position Down-“AND” - The alarm signal occurred only
when both sensor signals (PIR & MW) are present at
the same time.
Position Up-“OR“- The alarm signal (relay activation)
occurred when one of the sensor signals (PIR & MW) is
present.
YOU MUST RESET THE DETECTOR BY DISCONNECT
POWER SUPPLY AND RECONNECT IT AFTER FEW
SECONDS.
RANGE ADJUSTMENT
“MW” POTENTIOMETER
– adjustments
according to protected area range- see fig.5.
The potentiometer at mid-scale is equivalent to a
distance of 15m, at min-scale – 7m.
Rotate the potentiometer clockwise to increase range,
counter-clockwise to decrease range.
Dimension change according to installation
location and room size.
“PIR” POTENTIOMETER
– adjustment
according to protected area range.
Use the Potentiometer marked “PIR” to adjust the
detection sensitivity between 15% and 100%,
according to
walk test in the protected area.
(Factory setting is 57%)
Rotate the potentiometer clockwise to increase range,
counter-clockwise to decrease range.
Fig. 6
Ceiling bracket base
Wall bracket base
Fig.7
TECHNICAL SPECIFICATION
Detection Method
Quad element PIR &
microwave pulse Doppler
Power Input
8.2 to 16 Vdc
Current Draw
Active : 25.5 mA
Standby: 16.5 mA
Temperature
Compensation
YES
Alarm Period
2 +/- 1 sec
Alarm Output
N.C 28Vdc 0.1 A with
10 Ohm series protection
resistors
Tamper Switch
N.C 28Vdc 0.1A with
10 Ohm series protection
resistor - open when
cover is removed
Warm Up Period
1 min
LED Indicator
Yellow LED is blinking
during warm up period
and self testing
Red LED: ON during
alarm
Green LED: PIR CHANNEL
Yellow LED: MW CHANNEL
Dimensions 123mm x 62mm x 38mm
Weight
120gr
CROW ELECTRONIC ENGINEERING LTD. ("Crow") - WARRANTY POLICY CERTIFICATE
This Warranty Certificate is given in favor of the purchaser (hereunder the "
Purchaser
") purchasing the products directly from Crow or from its authorized distributor.
Crow warrants these products to be free from defects in materials and workmanship under normal use and service for a period of 24 months from the last day of the week and
year whose numbers are printed on the printed circuit board inside these products (hereunder the "
Warranty Period
").
Subject to the provisions of this Warranty Certificate, during the Warranty Period, Crow undertakes, at its sole discretion and subject to Crow's procedures, as such procedures
are form time to time, to repair or replace, free of charge for materials and/or labor, products proved to be defective in materials or workmanship under normal use and service.
Repaired products shall be warranted for the remainder of the original Warranty Period.
All transportation costs and in-transit risk of loss or damage related, directly or indirectly, to products returned to Crow for repair or replacement shall be borne solely by the
Purchaser.
Crow's warranty under this Warranty Certificate does not cover products that is defective (or shall become defective) due to: (a) alteration of the products (or any part thereof) by
anyone other than Crow; (b) accident, abuse, negligence, or improper maintenance; (c) failure caused by a product which Crow did not provide; (d) failure caused by software or
hardware which Crow did not provide; (e) use or storage other than in accordance with Crow’s specified operating and storage instructions.
There are no warranties, expressed or implied, of merchantability or fitness of the products for a particular purpose or otherwise, which extend beyond the description on the face
hereof.
This limited Warranty Certificate is the Purchaser's sole and exclusive remedy against Crow and Crow's sole and exclusive liability toward the Purchaser in connection with the
products, including without limitation - for defects or malfunctions of the products. This Warranty Certificate replaces all other warranties and liabilities, whether oral, written, (non-
mandatory) statutory, contractual, in tort or otherwise.
In no case shall Crow be liable to anyone for any consequential or incidental damages (inclusive of loss of profit, and whether occasioned by negligence of the Crow or any third
party on its behalf) for breach of this or any other warranty, expressed or implied, or upon any other basis of liability whatsoever. Crow does not represent that these products
can not be compromised or circumvented; that these products will prevent any person injury or property loss or damage by burglary, robbery, fire or otherwise; or that these
products will in all cases provide adequate warning or protection.
Purchaser understands that a properly installed and maintained product may in some cases reduce the risk of burglary, fire, robbery or other events occurring without providing
an alarm, but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss or damage as a result.
Consequently, Crow shall have no liability for any personal injury; property damage or any other loss based on claim that these products failed to give any warning.
If Crow is held liable, whether directly or indirectly, for any loss or damage with regards to these products, regardless of cause or origin, Crow’s maximum liability shall not in any
case exceed the purchase price of these products, which shall be the complete and exclusive remedy against Crow.
P/N 7101572 REV. D Y.S - A.Y.
CROW ELECTRONIC ENGINEERING LTD.
ISRAEL
:
Crow Electronic Engineering Ltd.
12 Kineret St. Airport City
P.O. Box 293 Ben Gurion Airport , 70100
Tel: 972-3-9726000
Fax: 972-3-9726001
E-mail:
USA
:
2160 North Central Road,
Fort Lee, N.J. 07024
Tel: 1-800-GET CROW
or (201) 944 0005
Fax: (201) 944 1199
E-mail:
AUSTRALIA
:
429 Nepean HWY Brighton East Vic 3187
Tel: 61-3-9596 7222
Fax: 61-3-9596 0888
E-mail:
POLAND:
VIDICON SP. ZO. O.
15 Povazkowska St.
01 – 797 Warsaw Poland
Tel: 48 22 562 3000
Fax: 48 22 562 3030
E-mail:
LATIN AMERICA:
CROW LATIN AMERICA
5753 NW 151
ST
.Street
MIAMI LAKES,
FL 33014 – USA
Tel: +1-305-823-8700
Fax: +1-305-823-8711
E-mail:
ITALY
:
DEATRONIC
VIA Giulianello 4/14
00178 ROMA, ITALY
Tel: +39-0676-12912
Fax: +39-0676-12601
E-mail:
These instructions supersede all previous issues in circulation prior to January
2006.
7101572_D
- 2 -
After adjusting the sensitivity perform a walk test
to verify optimum correct sensitivity in the
protected area.
N345
