background image

15122806

5

9

11

10

12

10

Replacement Parts

15122806

4

NO. Description

Part No.

1 Hand Shower

5F0M0178

2 Aerator Assembly

5Q0M0025PL

Hand Shower Hose

51014603

3 Diverter Knob Assembly

9Q241700

Hot & Cold Supply

5G0M0237CC

9Q241800

Mounting Assembly

9Q221900NT

5L0P0120

Finished Cartridge Dome

9Q241900NT

9Q241500

Hex screw and Key 

4
5

7

6

Cartridge Nut

Mounting Base Screw

5T1A0003AL

Cartridge

5D0M0041PL

Hand Shower Outlet

5Y0011100

0

Diverter Cartridge

5MD0M0006

5T0F0143NT

Escutcheon

8

11

9

10

12 Handle Plug & Screw

9Q1229

13

16
17

14
15

Handle 

1

2

3

4

5

15
14

13

12
11
10

9

8

6

16

17

7

Mount handheld bracket onto spout base. Tighten using 
supplied hex wrench.

Attach hose to spout and handheld shower.
Once hand shower is attached turn on TUB FILLER and 
test the diverter

Turn on water supplies and check all connections for leaks. 
Check MANIFOLD connections for leaks.Remove foam 
protector and apply sealant to under side edge on 
ESCUTCHEON . Slide ESCUTCHEON down to finish floor. 
Press into place.Clean up excess sealant.

APPLY SEALANT

FOAM PROTECTOR

Installation is complete.

A

B

6mm hex wrench 

6mm hex wrench 

5T4000400ZZ0

6mm HEX WRENCH

2.5mm HEX WRENCH

13mm HEX WRENCH

2.5mm HEX WRENCH

14-05

Cleaning Instructions

Rinse away any traces of soap and gently dry with a clean, 

soft cloth after each use. Rinse completely with water and 

dry any overspray. This will maintain the finish and avoid 

water spotting. 

To remove mineral deposits, use a 50/50 solution of white 

vinegar and water. Do not allow the solution to soak on the 

product. 

Simichrome Polish® contains a protective film to enhance 

maintenance and is helpful in preventing water spot 

buildup. Follow instructions to ensure optimum results. 

Never use an abrasive material such as a brush or scouring 

pad to clean the surface. The use of abrasive cleaners, 

cleansers or disinfectants will alter the surface finish and 

void the warranty. 

Do not allow certain materials such as toothpaste, cologne, 

shaving cream, nail polish remover, vinegar, wine, drain 

and glass cleaners to remain on the surface. Prolonged 

contact will alter surface finishes and void the warranty.

We DO NOT recommend using any household cleaners 

as many can cause damage to the finish. 

Please see the website for care instructions for specific 

finishes. 

Summary of Contents for Leyden 14-05







Reviews: