background image

MODEL 2017-03 Up/Downconverter

1.0  General

1.1  Equipment Description 

The 2017-03 L-band Up/Downconverter converts 70 MHz to 950-1525 MHz (Up) and 950-1525 MHz to 70 

MHz (Down) in 1 MHz steps with low group delay and flat frequency response. Synthesized local oscillators 

(LO) provide frequency selection. Multi-function push button switches select the RF frequency, gain, and other 

parameters. Front panel LEDs provide indication of DC power (green), PLL alarm for up and downconverters 

(red), remote operation (yellow), and Upconverter mute (yellow). Gain can be manually controlled over a -10 to 

+30 dB range for the Upconverter and over a 0 to +50 dB range for the Downconverter as adjusted by the front 

panel multi-function push-button switches. Remote operation allows selection of frequency and gain. Parameter 

selection and frequency and gain settings appear on the LCD display. Connectors are BNC female for IF and 

the optional external reference input and output, and Type F female for RF.  LNB or SSPB +24 VDC and 10 

MHz reference can be inserted on the RF lines as added options.  A high stability (±0.01ppm) option is also 

available. It is powered by a 100-240 ± 10% VAC power supply and housed in a 1.75” X 19” X 16” 1RU 

chassis.  

MENU

EXECUTE

MODEL 2017

C

ROSS 

T

ECHNOLOGIES INC.

U  F=1525     G=10.0
D  F=1525     G=25.0

MUTE

UPCONVERTER

DOWNCONVERTER

REMOTE

ALARM POWER

ALARM

UP/DOWNCONVERTER

FRONT PANEL

AC

UPCONVERTER

GND

DOWNCONVERTER

J4

J3

J18

J2

RF IN

10 MHZ REF

10 MHZ

IF IN

EXT REF

LNB FUSE

F1

J1

IF OUT

OUTPUT

INPUT

DS8

VDC on RF

J10

AND

MONITOR

CONTROL

1

2

3

4

6

7

8

9

RF OUT

SSPB FUSE

J5

F2

DS7

+24 VDC

J20

REAR PANEL

Figure 1.1     Model 2017-03 Front and Rear Panels

70 

MHz 
OUT

.95

to 

1.525

 GHz 

IN

1750 MHz

BP

1820

MHz

2.7

to

3.3

GHz

.95 to 1.525 

GHz

BP

120 MHz

LP

CONTROLLER

U  F=1525    G=+00.0
D  F=1450    G=+25.0

..95 to 1.525 

GHz

70 

MHz

IN

.95 

to

1.525 

GHz 

OUT 

1750 MHz

BP

1680

or

1820

MHz

2.7

to

3.3

GHz

REF

REF

REF TO 

UP 

VCOS

var

atten

10MHz*

+24VDC*

10MHz*

+24VDC*

EXT

10MHz*

*OPTIONAL

var

atten

var

atten

INT

10MHz

Figure 1.2     Model 2017-03 Up/Downconverter Block Diagram

2017-03 Manual, Rev. N

 

    Page 3   

    

                   03/22/18

Summary of Contents for 2017-03






















Reviews: