background image

7

Power Cord

(If Used)

Insulation 

Blanket

Water

Line

House

Wiring

Drain 

Hose

Maximum

Drain Hose

Length 10'

Installation Instructions

 STEP 8  SLIDE DISHWASHER

 PARTIALLY INTO CABINET

DO NOT PUSH AGAINST FRONT PANEL WITH KNEES.
DAMAGE WILL OCCUR.

• Slide dishwasher into the opening a few inches at a time.

• As you proceed, pull the drain hose through the

opening under the sink. Stop pushing when the dish-
washer is a few inches forward of adjacent cabinetry.

• Make sure drain hose is not kinked under the dish-

washer and there is no interference with the water
line and wiring or any other component.

TIP:

 Position water line and house wiring on the fl oor 

to avoid interference with base of dishwasher.

 STEP 7  INSERT DRAIN HOSE

THROUGH 

CABINET

• Upright the dishwasher and position in front of the

opening. Insert drain hose into cabinet wall hole. 
If a power cord is used, guide the end through a 
separate hole.

 STEP 6 INSTALL DRAIN HOSE

• Install the screw type hose clamps to the drain hose.

hose, then tighten the screw type hose hose.

Do Not Push Against
Front Door Panel With 
Knee. Damage to The 
Door Panel Will Occur.

The drain hose installation hole

• Install the drain hose to the drain hose installation

Summary of Contents for ZDM6502AS












Reviews: