Cromptons Spinna Winna Operator'S Manual Download Page 13

Spinna Winna Operators Manual

Part No. 990xxx Issue 1

Page 13 of 31

PROBLEM

POSSIBLE CAUSE

SUGGESTED REMEDY

Badly adjusted micro switch.

Re adjust micro switch.
See C.D.S. manual.

Faulty solenoid.

Replace solenoid.

I have a C.D.S. mk5
validated coin entry which
does not release coins when
the handle is pulled back.

Faulty micro switch

Replace micro switch.

Intelligent tilt sensor not
adjusted correctly.

Re-adjust the intelligent tilt
sensor.
See section 5.2 page 14.

Faulty intelligent tilt pcb

Replace intelligent tilt pcb.

Coins which fall into the
winchute out of game time
are not being diverted to the
cashbox.

Jammed diverter flap

Check for free movement of
flap and clear any
obstructions.

The level of coins in the
payout hopper is too low.
Look for no red light on
changer panel.

Refill hopper with coins of
play.

The changer mech. does not
accept coins.

Faulty changer mech.

Replace changer mech.

Jammed payout hopper.

Check for any obstructions
preventing the hopper disc
rotating.

The changer mech. accepts
coins but the machine does
not give change.

Faulty hopper.

Replace hopper.

The software is displaying a
fault on the machine.

Check the information display
for a fault description and
remedy fault.
See section 6 page 26.

The ticket box is empty.

Refill tickets.
See section 5.10 page 24.

The count hopper is jammed.

Check for any obstructions
preventing the hopper disc
from rotating.

Faulty ticket dispenser.

Replace ticket dispenser.

Faulty count hopper.

Replace count hopper.

The machine does not payout
tickets.

The ticket dispenser is
jammed.

Clear ticket jam from the
dispenser.

The bob tilt needs adjusting

Adjust the bob tilt.
See section 5.2 page 14.

The alarm does not sound
when the machine is rocked.

Faulty speaker

Replace speaker.

The slam tilt needs adjusting.

Adjust the slam tilt.
See section 5.2 page 14.

Faulty speaker

Replace speaker.

The alarm does not sound
when the payout doors are
struck.

Damaged slam tilt

Replace slam tilt.

Summary of Contents for Spinna Winna
































Reviews: