background image

Visit us at 

crlaurence.com 

for international toll free information                                 6

A

C.R. LAURENCE Co., INC.

OPERATION

Initial Operation

1.  Insert charged battery in handle and secure 

     with release button.  The spring must snap 
     into place.

2.  Separate the battery from the tool by pressing 

     the release button below the handle.

Charging Process

1.  Carefully insert the battery into the base of 

     the tool.  Pay attention to the correct 
     direction and do not insert the battery 
     the wrong way.

2.  Insert the output plug of the device into the 

     left side of the base.

3.  Insert the power plug of the device into 

     electrical socket (up to 230V).

4.  When the red indicator lights up the battery 

     is being charged.  This process lasts 
     approximately 1-1.5 hours (for fast charge).  
     The red indicator lamp switches automatically 
     off after 1-1.5 hours (for fast charge), and 
     the green indicator lights up. This means that 
     the battery has been fully recharged.  Only then
     can the power plug be pulled out of the socket.  
     The battery can then be taken out of the base 
     and used immediately.

CAUTION

:

•    The battery must be charged up before you first use your machine.  The battery only reaches its 

     full capacity after several charges.

•    Avoid repeated consecutive rapid charges of the battery.  Do not recharge after using only briefly.
•    The battery and the power supply unit warm up during the charge process.  This is not a malfunction.

Cordless Drill
Battery
Release Button

1

2

3

Plug (AC)

Charger

Battery

Red Indicator

Green Indicator

1

2

3

4

5

1

3

2

1

2

5

4

3

Summary of Contents for LD147









Reviews: