background image

 

REMOTE OPERATION QUICK GUIDE 

 
 
 
 

START

LOCK

UNLOCK

REMOTE 

#4

#3

#2

#1

2ND VEHICLE

TRUNK

(AUX#3)

(AUX#2)

(AUX#4)

STARTER

#5

CRIMESTOPPER

 
 
 
 
 

NOTE: BUTTON #3 and #4 Remote Start/Trunk 

There is a deliberate delay or 2 presses (Optional) built into the system on button #4 and #3 to help prevent 
accidental  remote  starting  from  the  remote  being  in  your  pocket  or  purse.    During  normal  use,  if  you  press 
button #4 or #3 too quickly, the system may not start the engine or open trunk. 

 
 

*NEW* Double Button Press for Remote start and Trunk release: 

This option will allow you to change whether the Remote starter and Trunk release activate by a single ½  
second press or a double button ½ second press. Check with your installer or follow programming option 
instructions in the installation manual.

 

 

Replacement Battery 

GP23A (12volt) 

OPERATION: 

 

BUTTON 1 (Lock Symbol): 

·

  Press and release to Lock doors. 

·

  Press and Hold for more than 3 seconds to 

activate “Panic” feature. 

 

BUTTON 2 (Unlock Symbol): 

·

  Press and release to Unlock doors. 

·

  Press 2 times for Driver Door Priority Unlock. 

 

BUTTON 3 (Trunk Symbol): 

·

  Press and Hold for ½ second or press twice to 

activate trunk pop. 

 

BUTTON 4 (Start): 

·

  Press and Hold for ½ second or press twice to 

Start/Stop Engine. 

 

BUTTON

 5 (Vehicle #2/ AUX#2/AUX#3/AUX#4) 

§

 

Veh #2 : Press and Hold for 2 sec.   

§

 

AUX #2: Press button 5 then press button 1. 

§

 

AUX #3: Press button 5 then press button 2. 

§

 

AUX #4: Press button 5 then press button 4. 

 

Summary of Contents for Super Rage CS-2011DP

















Reviews: