CrimeStopper PARK-PMCU Installation Manual Download Page 31

Page: 31 / 88

Troubleshooting

TROUBLESHOOTING

After the installation, the audible alert doesn’t work.

A. Are all of the cables connected properly?

B. Is the vehicles Ignition ON?

There is a damaged sensor detected.

A. Are all of the sensors plugged into the main control unit correctly and tightly?

B. Is there a sensor wire broken or damaged?

C. Is the sensor covered by snow or mud?

D. Is the sensor itself damaged?

Getting a false warning.

A. Are all of the sensors plugged into the main control unit correctly and tightly?

B. Do any of the sensors detect the ground?

Display alarm sound is too low or too high.

A. Press the SET button to adjust the volume to a suitable level

Any other questions should be directed to CrimeStopper technical support at 1-800-998-6880.

Summary of Contents for PARK-PMCU

























































































Search results

Summary of Contents for PARK-PMCU

Reviews:

Related manuals for PARK-PMCU

Brands by name

Popular brands

CrimeStopper PARK-PMCU, Installation Manual

Search results

Summary of Contents for PARK-PMCU

Reviews:

Related manuals for PARK-PMCU

Brands by name

Popular brands