background image

 

OPERATION INSTRUCTIONS  

 
ARMING 

To arm the alarm and lock the doors, press the Lock button on the transmitter.  You will hear a single siren chirp 
and  the  lights  will  flash  once.  The  system  will  arm,  the  doors  will  lock  and  the  starter  will  be  disabled  if  these 
optional features are installed. The red LED in the vehicle will start flashing after 5 seconds.  After a short delay 
to allow vehicle and electronics to stabilize the system will be completely armed. 
 

DISARMING 

Press the Unlock button on the transmitter to disarm the alarm.  You will hear 2 siren chirps and the lights will 
flash twice.  The LED stops flashing.  Door will unlock and dome light will turn on if the options are installed.   
 

SELECTIVE SILENT ARM/DISARM THROUGH REMOTE CONTROL 

This system can be armed and disarmed without siren chirps on an “as needed” basis. Press and release the 
Silent Button for arm/disarm without siren chirps. 
 

PROGRAMMABLE SILENT ARM / DISARM MODE (CHIRP DEFEAT) 

The system can be silently armed and disarmed as normal with Lock/Unlock Buttons, but no siren chirp.  See 
alarm programming option (#8) to enable or disable this feature.   

 
PASSIVE ARMING / PASSIVE LOCK MODES / PASSIVE CHIRP COUNTDOWN 

If  programmed,  passive  (Automatic)  Arming  will  occur  30  Seconds  after  the  ignition  is  turned  off  and  the  last 
door has been closed.  The LED will begin flashing rapidly while counting down.  If a door or hood is reopened, 
the system  will  wait  (LED off)  for the  door or  zone to close before  arming.   The  unit  will flash the lights once. 
Doors  will  lock  if  passive  locking  is  selected.    May  qualify  for  insurance  discounts-check  with  your  agent  or 
proprietor.    When  the  Unit  is  programmed  for  Passive  Chirp  Countdown,  the  siren  will  chirp  during  passive 
countdown, as an audible warning that arming will occur.  This siren will emit a chirp every 2 seconds as soon 
as the last door is closed until the system arms 30 seconds later. 
 

REMOTE PANIC PROTECTION 

To sound the alarm upon command (panic), press and hold the Lock Button for at least 2 seconds until the siren 
sounds.  Press the Unlock Button to reset panic mode. 
 

Summary of Contents for Fortress FS-20













Reviews: