background image

WIRING 

 

VIOLET WIRE: (+) DOOR TRIGGER INPUT 

Same as GREEN wire [below] except this wire is used for vehicles that show a positive voltage (12 volts) when the 
door is open such as many Ford, Lincoln, Mercury vehicles. 

 

BLUE WIRE: (-) HOOD/TRUNK INPUT 

This wire is an input trigger for a grounding hood or trunk pin switch.  Connect to existing hood and trunk pin switches 
that read ground when open.  If no existing switches are available, install  new pin switches.  Note: DO NOT mount new 
pin switches in water pathways.  

 

GREEN WIRE: (-) DOOR TRIGGER INPUT 

Identify the wire that reads Ground when any door is open and 12 volts when all doors are closed. 

 

YELLOW WIRE: IGNITION SWITCHED “ON” AND “START” +12 VOLTS 

Connect to an ignition wire (or fuse in the fuse box) that shows +12 Volts when the key in both “On” and “Start” 
positions. 

 

BROWN/WHITE WIRE: (-) HORN HONK OUTPUT (Optional, May Require Relay) 

This wire provides a pulsed (-) negative output for honking the vehicle’s horn when the system is tripped or when panic 
is activated.  Connect this wire to Negative Horn trigger wire in the steering column or to a relay on vehicles with a 
positive horn circuit.

 

 

WHITE WIRE: +12V FLASHING PARKING LIGHT

 

OUTPUT (15 Amp Fuse) 

Connect to switched parking light wire at back of light switch.  If this is not possible, connect directly to one of the 
parking lights at the front of the vehicle.  European vehicles require separate right and left circuits.  Use a dual relay or 
2 diodes to separate the output signal. 

 

BROWN WIRE: (+) SIREN OUTPUT (3 Amp Max.) 

Connect to RED siren wire. 

 

RED WIRE: +12V POWER INPUT (15 Amp Fuse) 

Connect to +12 Volt source with supplied fuse & holder.   Recommended location for this connection is at the vehicle 
battery positive terminal. 

 

BLACK WIRE: SYSTEM CHASSIS GROUND 
THIS WIRE MUST BE CONNECTED TO CHASSIS METAL OF THE VEHICLE.

  Scrape away any paint or dirt from 

the connection point to ensure a good connection. We recommend the kick panel area for your ground point. 

 

2 PIN PLUG (WHITE): PROGRAM/OVERRIDE PUSH BUTTON 

 

2 PIN PLUG (RED): LED INDICATOR (RED FLASHING LIGHT) 

 

Summary of Contents for CS-2100










Reviews: