Arming
the Crime Guard system turns on the antitheft protection, disables the
vehicle’s starter and locks the doors (provided an interface is installed). Once the
system is
Armed
, any intrusion attempt will
Activate
it, sounding the siren and
flashing the lights to attract attention.
Disarming
the system turns off the
protection, allowing normal use of the vehicle.
There are three methods of Arming the security system:
1- The first method is to use the transmitter or transceiver, by pressing and
releasing its “Arm/Lock” button. The system must not be in Alarm Valet
Mode (page 23-24), and the vehicle’s ignition switch must be off. Every press
of the “Arm/Lock” button arms the system, even if it is already armed.
2- The second method is to press and release the transmitter or transceiver’s “
II
”
button twice within 5 seconds. This is “Silent Arming”.
3- The third method is Last Door Arming, which configures the system to
automatically arm every time you exit the vehicle. This method of arming is
programmable, and may be used or not used as desired.
Page 6
USING YOUR CRIME GUARD SYSTEM
To Arm the System:
Press & Release the “Arm/Lock” Button ( ) on Either
REMOTE ARMING BY TRANSMITTER OR TRANSCEIVER
* An optional doorlock interface must be installed
THE DOORS WILL LOCK*
THE PARKING LIGHTS
FLASH TWICE
TO CONFIRM
ARMING
THE SIREN CHIRPS TWICE
TO CONFIRM ARMING
Upon Arming the System will:
• The siren will chirp twice (or four times if a zone is bypassed) unless the silent
arming procedure is followed.
• The parking lights will flash twice (or four times if a zone is bypassed).
• The doors will lock*.
U
Page 43
program the feature, follow Steps 1 to 4 on page 28; at Step 4 the Valet Switch
will be pressed and released thirty one times. The system’s response will be thirty
one siren chirps, and the Status Light flashing thirty one times, pausing, then
repeating. Within 10 seconds, press and release the transmitter’s "Arm/Lock"
button to turn on the Turbo Timer feature (the siren will chirp once) or the
"Disarm/Unlock" button to turn it off (the siren will chirp twice).
Your Crime Guard 850i
4
e system is capable of being operated by as many as
four controllers; these can be any combination of standard Crime Guard transmitters
or Omega Echo transceivers. Regardless of which, the transmitter or transceiver
must be encoded, or programmed, to the system in order to operate it (excepting
the originals, which were programmed at the factory). This programming
procedure is identical for a transmitter or Echo transceiver. To program
additional or replacement transmitters or transceivers, follow this procedure:
Have all of the transmitters or transceivers at hand (when one is programmed, all
others are erased).
Step 1 Turn the vehicle’s ignition “on”.
Step 2 Within 5 seconds of turning "on" the ignition, press the Valet Switch 5
times. The siren will chirp once, confirming that the system is ready to
learn a transmitter.
Step 3 Within 10 seconds press and release the “Arm/Lock” button (the “locked
padlock” graphic). The siren will chirp once, confirming that the system
learned the transmitter.
Step 4 Repeat the previous step for each transmitter or transceiver which is to
operate the system.
Only the “Arm/Lock” button is pressed in programming; when it is learned all of
the other buttons’ functions are automatically assigned. The system will remove
itself from the programming mode if 10 seconds expire without its receiving a
signal, if the ignition is turned “off”, or upon four transmitters or transceivers
being programmed into the system.
Please note that programming a transmitter to the system will activate the
audible Unauthorized Transmitter Alert warning and the extended Status Light
PROGRAMMING TRANSMITTERS
OR ECHO TRANSCEIVERS
