background image

Page 22

To custom program a new SecureCode:

 

Follow Steps 1 to 4 on page 20; at Step 4 the Valet Switch will be pressed and

released once (the siren chirps once) to access “feature number one”.

 

Within 10 seconds slowly press and release the transmitter’s Upper Left “Lock”

Button the number of times equal to the desired SecureCode for stage 1, allow the
system to respond to each transmitter button press with a siren chirp before
pressing the button again.

 

After entering the first stage by pressing the transmitter Upper Left “Lock” Button

the desired number of times, and receiving a chirp for each press, wait for the
system, after the final button press, to chirp the siren again the total number of
times that the button was pressed.

Continue 

to configure stage 2 of the SecureCode by now pressing and releasing

the Upper Right “Unlock” Button the number of times desired for the stage 2.
This should be done in the exact same fashion as the stage 1 entry- press the Upper
Right “Unlock” button, wait for a single chirp before pressing the button again,
and then when final button press is done, wait after the single chirp for the siren

PROGRAMMABLE  FEATURES

This section explains each of the programmable features in detail, notes the
factory default setting, and includes programming information as needed..

Feature #1   SecureCode Emergency Override      

(Factory Default

                        Setting 1 Press)

SecureCode is a unique patented feature which allows you to custom select the
number of Valet Switch presses in two stages, instead of a single “1 press”, which
would be required in order to perform an Emergency Override.  If any of the three
anti-carjacking  features are utilized, a customized SecureCode would also be
required to turn it off once it is fully activated.

How It Works

:

When a customized SecureCode has been programmed, when performing an
Emergency Override two separate stages of valet switch presses are required.  Each
of these stages may be from 1 to 9 Valet Switch presses.  The system will not disarm
after the initial Valet Switch entry, but pause and chirp the siren before continuing
to sound.  At this point the stage #2 entry must be made within 10 seconds.  If both
stages’ entries are correct, the system will disarm shortly after the stage #2 entry.

After a failed attempt to achieve SecureCode, the ignition switch must be turned

off, then on again before another attempt is made.  Should two failed SecureCode
attempts be made, the system will ignore any further presses of the Valet Switch for
two minutes.  If this occurs, the system will reset to the armed state, then sound the
siren twice after 2 minutes to indicate that another attempt may be made to achieve
a SecureCode Emergency Override.

If the SecureCode entry of the Valet Switch is the “as received” default

setting of “1 press”, the system will disarm the moment the Valet Switch is
released from the single press.  If a customized SecureCode has been
programmed, the system will disarm a few seconds after the correct entry.
If an incorrect entry is made, the system will not disarm.  See page 22 for a
complete explanation of a customized SecureCode operation.

Valet Mode:

Whereas Emergency Override disarms an armed or sounding alarm, a
similar procedure is the Valet Mode, which basically turns the system “off”,
and prevents it from arming or performing any automatic arming operations
which may be programmed to occur.  Valet Mode is explained on page 14.

Page 11

Upon Activating Panic:

 The electronic siren will sound.

 The vehicle’s exterior parking lights will flash.

 *The vehicle’s doors will lock, or unlock, depending on the method

      used to activate Remote Panic- the Upper Left “Lock” Button or the
     Upper Right “Unlock” Button.

ENTER THE VEHICLE

AND USE YOUR KEY TO
TURN THE IGNITION ON

    WITHIN 5
 SECONDS OF
TURNING THE
IGNITION ON,
  ENTER THE
SECURECODE BY
PRESSING THE
VALET SWITCH

THE SYSTEM WILL DISARM

ENHANCED  REMOTE  PANIC

 Hold 3
seconds

 Hold 3
seconds

OR

O

OR

R

OR

 To Activate “Remote Panic”:

 

Press & Hold for 3 Seconds  the Upper Left

 “Lock” Button (     )  OR  the Upper

    Right “Unlock” Button (     )

U

THE SIREN SOUNDS

THE PARKING LIGHTS

WILL FLASH

THE DOORS WILL

LOCK OR UNLOCK*

Summary of Contents for 533i 4

















Reviews: