Cretors RINGMASTER LITE Manual Download Page 2

 

 

   RML-O-S 

9 SEPT 2019 

 

 

I.

 

SAFETY FIRST  

 

The information in this manual is essential for the safe installation and 
maintenance of your Cretors cotton candy machine.  The manual must be 
read and understood before installing, operating or maintaining this 
equipment or equivalent training must be provided.

 

 
 

 

"The employer shall instruct each employee in the recognition and avoidance 
of unsafe conditions and the regulations applicable to his work environment 
to control or eliminate any hazards or other exposure to illness or injury".        
Ref.:  29 CFR 1926.20 (b)(4)(a)(2)

 

 
 

 

It is understood that safety rules within individual companies vary.  If a 
conflict exists between the safety procedures contained in this manual and 
the rules of a using company, the more stringent rule should take 
precedence.

 

 
 

II.

 

INTRODUCTION 

This manual is filled with timesaving and money-saving information regarding your Cretors 
machine.  There is nothing, however, more important than the safety aids and warnings that are 
found throughout this document.  The Safety Alert Symbol is used to identify topics of primary 
safety concern wherever they appear.  Furthermore, a separate section has been included which 
deals exclusively with operation and accident prevention.  
 
If, after reviewing this manual, anything is unclear or technical problems are encountered, contact 
the dealer from whom you purchased your machine for assistance.  If there are any additional 
questions, feel free to contact our Customer Service Department at the address and/or phone 
number listed on the back cover of this manual.  Always have the model and serial number of your 
machine available to assist in obtaining the correct information. 
 

III.

 

SAFETY ALERT SYMBOL 

The symbol shown below is used to call your attention to instructions concerning your personal 
safety and the safety of others.  Watch this symbol.  It points out important safety precautions.  It 
means "ATTENTION!  Become Alert!  Your personal safety is involved!"  Read the message that 
follows and be alert to the risk of personal injury or death. 
 

 

Summary of Contents for RINGMASTER LITE












Reviews: