manualshive.com logo in svg

Crestron TST-902-DSW, Product Manual

Share
Download
Crestron TST-902-DSW Product Manual Download Page 99

94 • TST-902

Product Manual — Doc. 7750C

Standby Timeout

Tap Standby Timeout on the TST-902 Setup screen to display the Standby Timeout screen.

Use the Standby Timeout screen to set the standby timeout settings for the touch screen.

l

Tap the up and down arrow buttons under Standby (on the left of the screen) to set the
touch screen standby timeout duration from 0 to 120 seconds when it is undocked. Select
"0" to turn off standby timeout.

l

Tap the up and down arrow buttons under Power Down to set the power down duration
from 0 to 240 seconds when it is undocked. Select "0" to turn off the power down
behavior.

l

Tap the up and down arrow buttons under Standby (on the right of the screen) to set the
touch screen standby timeout duration from 0 to 120 seconds when it is docked. Select
"0" to turn off standby timeout.

Summary of Contents for TST-902-DSW

























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands