background image

SmarTouch™ Control Processor 

Crestron 

ST-CP

 

Return and Warranty Policies 

Merchandise Returns / Repair Service 

1.  No merchandise may be returned for credit, exchange, or service without prior authorization 

from CRESTRON. To obtain warranty service for CRESTRON products, contact the factory 
and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying 
the nature of the problem, name and phone number of contact person, RMA number, and 
return address. 

2.  Products may be returned for credit, exchange, or service with a CRESTRON Return 

Merchandise Authorization (RMA) number. Authorized returns must be shipped freight 
prepaid to CRESTRON, Cresskill, N.J., or its authorized subsidiaries, with RMA number 
clearly marked on the outside of all cartons. Shipments arriving freight collect or without an 
RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and 
absolute discretion to charge a 15% restocking fee, plus shipping costs, on any products 
returned with an RMA. 

3.  Return freight charges following repair of items under warranty shall be paid by CRESTRON, 

shipping by standard ground carrier. In the event repairs are found to be non-warranty, return 
freight costs shall be paid by the purchaser. 

CRESTRON Limited Warranty 

CRESTRON ELECTRONICS, Inc. warrants its products to be free from manufacturing defects in 
materials and workmanship under normal use for a period of three (3) years from the date of 
purchase from CRESTRON, with the following exceptions: disk drives and any other moving or 
rotating mechanical parts, pan/tilt heads and power supplies are covered for a period of one (1) 
year; touchscreen display and overlay components are covered for 90 days; batteries and 
incandescent lamps are not covered.  
This warranty extends to products purchased directly from CRESTRON or an authorized 
CRESTRON dealer. Purchasers should inquire of the dealer regarding the nature and extent of the 
dealer's warranty, if any. 
CRESTRON shall not be liable to honor the terms of this warranty if the product has been used in 
any application other than that for which it was intended, or if it has been subjected to misuse, 
accidental damage, modification, or improper installation procedures. Furthermore, this warranty 
does not cover any product that has had the serial number altered, defaced, or removed.  
This warranty shall be the sole and exclusive remedy to the original purchaser. In no event shall 
CRESTRON be liable for incidental or consequential damages of any kind (property or economic 
damages inclusive) arising from the sale or use of this equipment. CRESTRON is not liable for 
any claim made by a third party or made by the purchaser for a third party.  
CRESTRON shall, at its option, repair or replace any product found defective, without charge for 
parts or labor. Repaired or replaced equipment and parts supplied under this warranty shall be 
covered only by the unexpired portion of the warranty. 
Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed 
or implied, nor authorizes any other party to offer any other party to offer any warranty, including 
any implied warranties of merchantability or fitness for a particular purpose. Any implied 
warranties that may be imposed by law are limited to the terms of this limited warranty. This 
warranty statement supercedes all previous warranties. 

Trademark Information

 

All brand names, product names, and trademarks are the sole property of their respective owners. 
Windows is a registered trademark of Microsoft Corporation. Windows95/98/Me/XP and 
WindowsNT/2000 are trademarks of Microsoft Corporation

 

 

12  

  SmarTouch™ Control Processor: ST-CP 

Operations Guide - DOC. 5820 

Summary of Contents for SmartTouch ST-CP





















Reviews: